Zigbee 3.0 USB Dongle Plus EFR32MG21 Universal Open Source Hub Gateway Works with Home Assistant openHAB Zigbee2MQTT ZHA NCP

Zigbee 3.0 USB Dongle Plus EFR32MG21 Universal Open Source Hub Gateway Works with Home Assistant openHAB Zigbee2MQTT ZHA NCP

• I am an international seller，100% brand new and of high quality

Our shop sells the most popular 3C consumer electronics products,such as mobile phone accessories,computer accessories,game peripherals,smart wearables,and follow the most popular fashion trends. If you like our products,please follow us,become our follower and fan.We will provide you with the most popular products to satisfy your fashion shopping experience.Communication method : zigbee,WI-FIState of Assembly : Ready-to-GoModel Number : ZigBee 3.0 USB HubBrand Name : SZKOSTONOrigin : Mainland ChinaCertification : CE,RoHSZigbee 3.0 USB Dongle Plus EFR32MG21 Universal Open Source Hub Gateway Works with Home Assistant openHAB Zigbee2MQTT ZHA NCPSZKOSTON Zigbee 3.0 USB Dongle Plus is a universal Zigbee USB stick. It can be used as a Zigbee gateway in Home Assistant, openHAB, Zigbee2MQTT, or other open-source platforms to locally control all your Zigbee devices, so you don't need to invest in different brands' Zigbee hubs, all you need is a universal gateway - Dongle Plus!SZKOSTON dongle plus has a wide range of supported devices, such as ZBMINI-L, SNZB01, SNZB02, SNZB03, SNZB04, S26R2ZB, S40 LITE ZB. Dongle Plus is pre-flashed with coordinator firmware, you can also flash router firmware to extend the network range.SZKOSTON Dongle Plus support a variety of common systems, like Linux, Ubuntu, Raspbian, Windows, macOS (Windows and macOS require corresponding driver installation).If the device is following Zigbee standards it is possible it will work with other gateway solutions, it is just not confirmed as working yet!1、Pre-flashed with EZSP v8 (EmberZNet Serial Protocol version 8)2、Can use ZHA in Home Assistant or Zigbee2MQTT (pre-alpha)3、Base on EFR32MG21+CH340E4、+20dBm output gain，PCB antenna5、Plastic Shell6、Support OTA Via Uart (Press the BOOT button,then press and release the nRST button, fiannaly release the BOOT button)7、Baud rate ：115200It comes pre-flashed with an unsigned EmberZNet 6.7.9 Zigbee NCP application firmware with Silabs standard EZSP v8 (EmberZNet Serial Protocol version 8) interface enabled as well as the standard Silabs Gecko Bootloader firmware for recovery, meaning it can be used either as-is out-of-the-box or flashed with custom application firmware via USB.Hardware is at its core based onSilicon Labs EFR32MG21 Series 2 Multiprotocol Wireless SoC(part numberEFR32MG21A020F768IM32) and aWCH CH340E USB to Serial/UART Bridge Controller. While it only has a PCB circuit board antenna the radio has an integrated +20 dBm Power Amplifier (output power) and -104.5 dBm Receive Sensitivity which should be made for a very good Zigbee coordinator or Zigbee router if both hardware and firmware were properly implemented.TheElelabs EZSP Firmware Upgrade Utility(https://github.com/Elelabs/elelabs-zigbee-ezsp-utility/) orwalthowd firmware update Docker image(https://github.com/walthowd/husbzb-firmware) can be used to flash the firmware to a newer or older version. New and old firmware official images are currently being provided at github (https://github.com/xsp1989/zigbeeFirmware/tree/master/firmware/Zigbee3.0_Dongle-NoSigned/EZSPNotice:Please allow 1-3mm difference due to manual measurement.Due to different displays and different lighting, pictures may not show the actual color of the item. thanks for your understanding