XYCD63 30A Battery Charging Control Module Full Power Off

UP on: Short pre to switch display% and time, long pre for 5 seconds to switch mode, charging mode: IN, discharging mode: OUT

Charging mode IN

By setting the upper limit voltage UP and the lower limit voltage dn; when the battery voltage ≤ the lower limit voltage dn, the relay is turned on, and the charger starts to charge the battery; when the battery voltage ≥ the upper limit voltage UP, the relay is disconnected to complete an automatic charging; the relay is turned on, IN flashes, indicating that it is charging.

Discharge mode OUT

By setting the upper limit voltage UP and the lower limit voltage dn; when the battery voltage ≥ the upper limit voltage UP, the relay is turned on and starts to discharge; when the battery voltage ≤ the lower limit voltage dn, the relay is disconnected to complete an automatic discharge function; the relay is turned on and OUT flashes, Indicates that it is discharging.

Note: This product is a simple voltage controller, which uses a relay to turn on and off the output. It only functions as a switch and cannot be transformed.

Function Description:

1. Calculation of voltage percentage: battery voltage/(upper limit voltage-lower limit voltage)

2. Key function:

UP on: Short pre to switch display% and time, long pre for 5 seconds to switch mode, charging mode: IN, discharging mode: OUT

SET on: short pre to view the currently set ; long pre SET on to enter the parameter setting interface, set UP: voltage upper limit, dn: voltage lower limit, OP: conduction time, dOP: delay conduction time (0-999 seconds) , There is FOP in discharge mode: forced conduction time (0-10 seconds)

DOWN on: Short pre to turn off/on the relay enable (emergency stop function) ar it is turned off, the LCD display is OFF, and the relay is disconnected

Long pre the DOWN on to set the status of the LCD backlight. L-P: OFF, the backlight is always on, ON: the backlight will automatically go out ar 5-10 minutes; any key to wake up ar it goes out.

3. Parameter setting

A. Long pre the SET key to enter the parameter setting interface;

B. Ar entering the parameter setting interface, short pre the SET key to switch the set ;

C. Ar selecting the parameter, you can set it through the UP/DOWN key, and support short pre and long pre;

D. If you want to set other , repeat steps b) and c);

E. Ar all parameter settings are completed, long pre the SET on to exit and save;

3.1 Charge/discharge time control function

When the set time parameter OP is non-zero, start the charge/discharge time control; when the relay is turned on and open for a charge/discharge, start timing; when the timing is completed, the relay is automatically disconnected to complete a charge/discharge proce; if the timing is completed, charge In mode, detection voltage upper limit voltage UP, the charging time control function is automatically turned off, and the flashing display H:ER reminds the user that the time parameter setting is unreasonable; pre any key to stop flashing;

When the charging/discharging time control is not turned on, the product will record the complete time once. When entering the time display interface, the charging time flashes; it will be cleared when it exits the time display interface or the charging is turned on (relay is turned on);

3.2 Automatic parameter detection:

Ar setting the and exiting, if the lower voltage limit dn ≥ the upper limit voltage up, the system will flash "ERR" as a reminder;

3.3 Delayed conduction function dOP (0~999 seconds):

The interval between charging/discharging once and turning on again;

3.4 Discharge conduction forced start time FOP (0~10S):

Ar the relay conduction conditions are met, the relay is forced to conduct (0~10S), and the battery voltage is detected again; this function is mainly for the discharge function, and some test loads will be instantly pulled down to the lower limit voltage at the moment of conduction, causing false triering The relay is disconnected and the normal discharge proce cannot be carried out;

Common failure analysis

Q: How much V level is suitable for use? How much V voltage is suitable for this product?

Answer: This model is suitable for use in the voltage range of minimum 6V and maximum 60V, and the maximum expenditure level is 48V, because the 48V battery is fully charged at about 60V, and it will burn at a higher level. If your battery is higher than 48V, please choose other models.

Question: The relay pops ar power-on!

Answer: This is because your charging current is too large or the battery capacity is too small. The upper voltage limit is reached immediately ar power-on. The relay is disconnected. Ar disconnection, the voltage drops rapidly to the lower voltage limit and starts charging again. When you need to reduce the charging current, usually the charging current is 1 to 1.5 of the battery capacity, such as 20AH battery charging current is generally around 2-3A! Note that high-current charging will cause the battery to heat up, accelerate aging, or even explode!

Q: What control method? Can it be recharged automatically? Can I charge while using it? Can it limit the current?

Answer: This is voltage control. For example, set the lower limit of voltage to 12.0V and upper limit of voltage to 14.5V. When the voltage is charged to 14.5V, the power will be cut off, and the voltage will be reduced to 12.0V. The relay will close and start charging; you can charge while using, and control the voltage. The method only functions to turn off and turn on, and cannot limit the current. The charging current depends entirely on your charger!

Question: Can the 24V battery be charged by inputting 12V, or can the 12V battery be charged by inputting 48V?

Answer: This model is a simple voltage controller, which only functions as a switch and cannot change the voltage to charge the battery, so you must prepare what kind of charger you want to charge the battery! neceary!

About shipping
Shipping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days ar buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties ores. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.