Winner Transfer Laser Dark No-Cut A Paper+B Paper 20 Sheets Heat Transfer Paper For Laser Printers With White Toner

Search WinnerTransfer Discover More Transfer Papers

1.The Laser no-cut transfer paper (A paper+ B paper) is easier to operate and suitable for beginners. Color is bright, image will completely transferred.

2.If there is white in the design, be sure to cover it with white when printing. Currently, only OKI C711WT or OKI941 printers are supported for cover. If the pattern does not contain white, you can use another brand of color laser printer.

3.Prepare pattern: the pattern must be a hollowed-out vector image in the format of CDR, EPS, AI. The supported formats are JPE, GIF, PNG, Otherwise, there will be no hollowed-out effect.

4.Tip: Start with a small diagram to avoid wasting fabric. 

5.SETTING: B paper to A paper, heat press machine parameter setting : 165℃, 60-90℃ secondes, hot peel.

A paper to cloth, heat press machine parameter setting : 165℃-175℃,15-30 secondes ,cold peel.

Temperature invariable appropriate increase pressure in order to increase the color and firmness of the pattern the pattern is covered with isolation paper and hot pressed for 5-10 seconds.

 

Heat press machine parameter setting:

160-175℃（320-347℉）,60s-90s, medium or light pressure. It is recommended that the heat press machine preheat for 5-10 minutes. When the temperature reaches the preset temperature, press the air pressure of the hot press for 5 seconds, so that the temperature of the hot pressing plate on the hot press and the silicone pad tend to be consistent, so that the next transfer is successful.

 

How to use:

1 PRINT

OKI printer Settings:

Select multi-function paper inlet, mirror print, then select PCS transfer mode and white CMYS mode to print (only for OKI C711WT or OKI 941 printers).

A paper: label paper, heavy/thickness: 120-180g.

Note: The pattern must be hollow vector map, the picture format is CDR, EPS, AI, other wise there is no hollow effect.

 

2 B Paper to A paper transfer

A paper with the image facing upwards, B paper with the blank side facing downwards, with a strip of separator paper between A paper and B paper to keep the image out of the way. Heat presses machine with medium or medium light pressure.

Note : A paper and B paper up and down alignment, temperature, time and pressure parameters: 160-175℃（320-347℉）60-90 seconds.

 

3 Peel

Hot peel (The transfer paper must not leave the ironing board to peel off the B paper. Even and horizonal hot peeling 5-10s for A4 size, and remember not to pause, To prevent burns, we recommend that wear gloves during this step.) Throw away B paper, keep A paper.

 

4 Cut

Cut off any excess glue marks on the edges before transferring.

 

5.Transfer

Transfer A paper image side down, Heat press machine for heavy pressing.

Note: 160-175°（320-347℉）15-30S，ordinary patterns do not need to adjust the pressure and temperature, just hot pressing 15-30 seconds, if there is a small part of the pattern, to increase the pressure of the heat press.

 

6 Peel Ensure cold peeling

Note: Peel off paper A at a constant speed.

 

7Reveal

Place silicone paper and press to fix the colour.

Note: 160℃（320℉）5 seconds, put the fabric on silicone plate of the heat press, cover the image with silicon paper, and heat press for 5-10 seconds.

 

8: DONE

Congratulations! Your DIY image transfer has been done.

Don't wash within 48 hours after transfer.

 

WASHING  INSTRUTIONS :

1.Don’t wash within 48 hours after transfer.2.Wash the garment before wearing.3.Don’t use bleach or alkaline detergent.4.Turn the garment inside out when washing.5.Don't soak to wash.6.Full spin cycle, cold water washing.7.No delicate washing.8.No tumble dry.9.Remove garment promptly after washing, colors may bleed if left wet too long.10.Unfold the transferred image, hang to dry naturally.

 

STORAGE INSTRUCTIONS:

1.Keep the image facing outside when fold the garment.2.Store the garment in a dry and cool place.3.Keep the unused transfer paper sealed and preserved.