WAVLINK Waterproof N300 Wireless Outdoor Access Point Extender with PoE Powered

*Power Over Ethernet: Integrated Power over Ethernet (PoE) enables power and network data connections to be consolidated into a single RJ-45 cable, allowing fix in areas without power outlets. It is equipped with passive PoE and also supports active PoE. You can use and connect your own active switch.

*IP67 Rated Weatherproof Case: The IP67-rated weatherproof and heat-resistant enclosure ensures continued operation in harsh outdoor environments, including extremely cold, hot or constantly humid climates. It can withstand a wide range of humidity and temperature (-10°C to 50°C or -14°F to 122°F), and has 15KV ESD and 6KV lightning protection.

*Multiple Working Modes: It supports four working modes. The repeater mode extends the WiFi coverage of an existing wireless network. Router mode creates an instant private wireless network, enabling multiple devices to share it. AP mode converts a wired network to a wireless one. AP+Repeater mode extends the range of a wireless network just using a repeater to amplify and relay the signal from an access point.

*Outdoor Access Point: It has a maximum coverage range of 150 meters, supports up to 32 devices, and provides 2.4GHz, 300Mbps, high-speed, and 100M Ethernet ports. Simple settings enable wireless optimization to improve the quality and effectiveness of link transmission. (Coverage may vary based on the actual environment.)

*Single-Band Range Extender: 802.11n Wireless technology, you can enhance your existing wireless coverage even in single-band range, providing speeds of up to 300Mbps on the 2.4GHz band. This allows you to enjoy high-speed downloading of your games, videos, and other files even in public areas.

WAVLINK 300Mbps Outdoor Access Point
The WAVLINK HighPower WiFi AP/Repeater/Extender is mainly used for providing free WiFi service in large areas such as factories, communities, streets, etc. The AP/Repeater/Extender can take an existing 2.4GHz wireless signal, repeat it, and extend it to a longer range where it is too far away for the router or access point to reach. And it can support 2.4G transmission speeds of up to 300Mbps. It has two external antennae, providing even better wireless performance, transmission rates, and stability. 

Applicable to Kinds of Weather
IP67-rated weatherproof and heat-resistant housing ensures continued operation in harsh outdoor environments. For example, it is sunny and exposed to the sun; it rains and is wet; it snows and freezes; and there is thunder and lightning.

Applicable to Multiple Scenarios
It is suitable for various large-scale outdoor scenes, whether it is your own yard, outdoor swimming pool, school, park, playground, or outdoor parking lot.

Waterproof Case Design
The waterproof housing has an IP67 rating for impressive dust and water resistance, allowing it to operate reliably even when exposed to harsh outdoor conditions or temporary rain.

7dBi Omni Directional Antennae
The high-gain antennae panel has two built-in 7-dBi omni directional antennaes, which are designed to strengthen the Wireless signal in one direction and make it more concentrated. And Wireless coverage in a specific direction is farther than omnidirectional antennaes.

Default setting
2.4G SSID: WAVLINK-N XXXX
Default IP: 192.168.10.1
Default Password: admin

How to fix Antennaes and Ethernet Cable?
1) Pass the RJ45 cable through the spiral cover.
2) Pass the RJ45 cable through the rubber seal.
3) Pass the RJ45 cable through the holder.
4) Connect the RJ45 cable to the RJ45 port.
5) Spin the 2.4G antennae into the 2.4G external RP-SMA connector.
6) Tighten to secure the holder.
7) Insert the rubber seal into the holder.
8) Tighten the screw cap with a screw.
Note: The PoE converter is not waterproof, please assmble it indoors. Please make sure your Ethernet cable is CAT5E or above certified and shorter than 100m.

Mount Steps for the Device
1) Fasten the main body holder.
2) Plug the device into the holder.
3) Connect one end of an Ethernet cable to the "PoE" port of the PoE converter.
4) Connect one end of another Ethernet cable to the "LAN DATA IN" port of the PoE converter, and connect the other end to a "LAN" port of your router.
5) Plug the Power Adapter into the power outlet.
6) Push the "ON/OFF" button on the PoE converter to power on.

Warm Tips
1.The PoE converter is not waterproof, please place it indoors.
2.Please make sure your Ethernet cable to the outdoor router is CAT5E or above certified and shorter than 100m.
3.Please fix the product 2-3meters above the ground for better performance.

Specification
1.Model: WL-WN570HN2-B
2.Ports: 1 x WAN/LAN 100Mbps
3.Button: 1 x Reset(8s); Status LED: 1 x Power, 1xWAN/LAN, 1 x WF, 3 x Signal
4.Power Supply: DC 54V/0.3A Power over Ethernet(Passive), DC 48V Power over Ethernet(Active)
5.Wireless Standard: IEEE 802.11 b/g/n
6.Frequency Band/Speed: 2.4GHz(300Mbps)
7.Antennae: 2 x 7dBi Omni Directional
8.Wireless Security: WPA-PSK/WPA2-PSK safety
9.Unit Size(without antennaes): 18cm x 5cm x 5cm/ 7.1in x 2in x 2in (L x W x H ); Antennae Length: 25cm
10.Ethernet Cable Length: 100cm
11.Power Adapter Cable Length: 120cm/47in
12.Operating Temperature: -10°C~50°C(-14°F~122°F)
13.Storage Temperature: -30°C~70°C(-22°F~158°F)
14.Distance:Outdoor 150m(Change with the Actual Environment)