SCULPFUN S10 Engraving Laser Module 10W High Density Laser

Features:

Wide Compatibility: Design with widely compatible structural connection device, which can be well adapted to different laser engraving and cutting machines, 3D printers, milling machines, etc. It can be installed on a variety of brand machines, such as SCULPFUN S9/S6pro/S6、ATOMSTACK A5/A5Pro, ORTUR(12V Version) laser engraving machine, or other DIY type machines.

Powerful High-Speed Air Assist: S10 is equipped with a high-speed air assist nozzle which has an advanced fluid mechanics design to better utilize the air pressure. When using the same air compressor, the S10 spray airflow faster. For example, when using 30l/min, 0.03mpa air compressor, the S10 nozzle will spray high-speed airflow up to 14.5m/s, which greatly improve the cutting penetration and cutting efficiency.

10W laser Module: The S10 laser output is increased to 10W, which is twice that of the S9. But S10 obtains the same ultra-thin laser beam with 0.08mm focus as S9, which means S10 has higher energy density, stronger cutting penetration and engraving capabilities.

Powerful and Clean: S10 shows comparable to industrial-grade wood cutting performance: First, the cutting efficiency is greatly improved, cut faster; Second, the cutting penetration is stronger, and many high-density woods can be cut; Third, the cutting surface is cleaner, the powerful airflow blows away the residue, so that there is no stain on the surface of the cutting object.

Great Design: Equipped with a detachable eye shield, which will not dazzle even without glasses. And easy to disassemble if you don't need it. And S10 laser module uses a common 12V/PWM modulation board, which can be adapted to common GRBL or motherboards. (check out product pictures for more details.)



Specification:

Compatibility: SCULPFUN S9/S6pro/S6, ATOMSTACK A5/A5Pro, ORTUR(12V Version), ELEKSMAKER or DIY 3D printers, machine

Engraving Material: All Kinds Of Wood (Including Walnut, Cherry And Other High-Density Wood), MDF, Zigzag, Cardboard, Plastic, Leather, Board, Aluminum Oxide, 304 Stainless Steel, Ceramic, Dark Stone

Cutting Material: All Kinds Of Wood (Including Walnut, Cherry And Other High-Density Wood), Mdf, Acrylic Board, Cardboard, Non-Woven, Bamboo, Leather, Some Plastic Boards, Boards

Circuit Board Size: 40x40mm

Circuit Board: 12V/PWM Modulation Board

Input voltage: 12V

Max Input of laser Module: 12V 5A

Wire Rod: HY2.0, 3Pin Terminal (3-core cable, A: PWM +, B: GND, C: VCC ).

Fan: 12V 0.15A 4020 fan

Fan Speed: 15000 rpm

Operating Temperature: -20 ℃ to 70 ℃

Package weight: 0.85kg/30oz

Packing size: 22.7x13.6x9.5cm/8.9x5.3x3.7in



Tip:

How to judge whether the S10 laser is suitable for use? You need to pay attention that the input voltage of the S10 laser is 12V, and the S10 is a 3pin interface, you can check the detailed pictures.



Note:

● Because of the powerful laser of S10, it is forbidden to run the engraving machine unattended. Pause it if you're not around.

● For detailed machine instructions, please refer to the manual for parameter settings.

● When operating the laser engraving machine, please install the laser protective cover; if it is not installed, you need to wear .

● Do not touch the laser with your hands, otherwise you may burn your hands.

● Please avoid strong impact on the machine.

● It is forbidden for children under 14 years old to use this product, and children over 14 years old need adult attended.

● Do not use the laser directly on any specular reflection object, which may cause injury to the operator or burn the laser.



Packing List:

1 x 7.5mm Inner Diameter Air Tube

1 x Acrylic Protective Cover

1 x S10 Laser Head

1 x Multifunctional Connector

1 x 50mm Measuring Column

1 x Screw And Tool Kit