NFLH LH-007 For Starline A91/B9/,Mobile Phone APP Controll Car GSM Two Way Car Alarm System,ely Start Engine

LH-007 mobile phone control car module Suit for starline A91 and B9 alarm system, perfectly compatible to upgrade old alarm system.

LH-007 Module Instructions for UseThank you very much for choosing the LH-007 mobile phone control module of NFLH series products in Shenzhen, China. This system is an upgrade module of the two-way alarm system, and adds the mobile phone control function on the basis of the two-way anti-theft device. This module completely reps the two-way e control, and the control of the car is no longer limited by distance.The e control and this module can be operated at the same time, and the status is automatically synchronized (the APP interface needs to be refreshed manually).LH-007 module adopts 2G communication module, power supply voltage 9-15V, power consumption current 20MA, external +12 power supply line and ON/ACC line (there are two lines at the alarm main control unit - red +12V, thiyellow ACC ).Use the following steps:installation method:1. Find the +12V (thired) connection on the main control unit of the car immobilizer. The white ON/ACC wire is connected to the thiyellow wire.2. Remove the cable from the box and rep it with a new cable. The blaterminal of the connecting wire is input to the box, and the other end is adapted to the special wire harne. The 8P end of the special wiring harne is connected to the 8P terminal on the control module, and the other end is connected to the 5P socket of the alarm control unit .3. The mobile phone control module can choose the appropriate alarm system model. The red key switch on the main box is fully enclosed, which is suitable for the starline a91 alarm system. Red key switch on the main box, 3 keyboard open, suitable for starline b9 alarm system and CENMAX ST-8A alarm system.4. Select the 2G SIM card and insert it into the control box, then connect the control box +12 power supply.Download the APP and register for certification:1. Scan the QR code on the side of the box, download and install the "NFLH" APP, download and open all permiion options, and agree to the permiion of the APP to push information to the mobile phone.2. After the download is complete, start registering the identity information (Note: Please use the commonly used email ae as the username, so that if you forget the paword in the future, it will become the only basis for retrieving the paword). The first line is to fill in the email ae;The second line is to set the APP login paword;The third line is to repeat the APP login paword;The fourth line is the IMEI number of the input device (the line on the baof the host);The fifth line is to enter your plate number.Use and operation:1. Log in to the APP: Log in to the APP, select "Login", enter the email ae and login paword ( save the paword), and cli"Login" to enter the main control interface.2. Copy the e control paword key: insert the KEY into the lohole and start the operation. Once calated according to OFF--ON--OFF, please operate continuously for at least 6 times (each action is completed within 1 second), and finally the KEY is in the OFF position. At this time, the green LED on the side of the module box fes rapidly, indicating that the e control can be copied. Clithe "Unlock" on of the two-way e for 0.5 seconds. The green LED is off, indicating a succeful copy.3. Open the APP, enter the main interface, and chewhether the orange signal icon in the upper left corner is orange.If it is orange, it means that the GSM card is working normally and can be operated directly.If the signal icon is gray, the SIM card is not suitable for the control module or the SIM card holder is loose and cannot connect to the network normally, please rep the SIM card. Or, disconnect the power, reconnect, wait for 5 minutes, refresh the APP interface status (icon in the upper right corner), and see if there is any change.APP function description:1. Lo;2. Unlock;3. e start;4. Stop the engine running;5. Backdoor e control;6. Positioning;7. Lift the window;8. Vehicle sound and light search;9. Anti-hiing mode;10. Set the temperature to start;11. Set the time interval to start;12. Module external temperature;13. Vehicle voltage;14. The first page;15. Map;16. My (menu);17. GSM signal strength;18. The second level menu;19. plate number;20. Update status;21. Alarm prompt;ysis of common fai probl:1. GSM is not connected, the system cannot be used at all: first chethe SIM card, you need a SIM card that supports 2G network GSM to use. After the SIM is working normally, the signal strength indicator on the upper left of the APP will change from gray to orange, indicating that the SIM is working.2. The code matching method between the LH007 system and the user alarm - use a white wire to quickly touch the 12V positive wire for at least 6 times, the green LED on the side of the 007 main box fes quickly, be sure to pre the two-way e control for a short time the unloon (0.5 seconds), the green LED is off, and the code matching is completed. If it does not succeed once, it is recommended to operate 2-3 times in a row to ensure that the pairing is absolutely succeful;3. The cannot locate the fault. Please cheif the is properly installed. must be pd on the dasard of the car. Don't forget any obstacles. signals cannot be received in buildings, signals need to be received in open areas. Signal. Princed bases, many bases will blo signals on a large scale.4. If the alarm information of the car cannot be received, please find the permiions in the phone settings, find the NFLH-APP, allow all permiions, and allow the APP to run in the background. IOS mobile phones, Huawei, Honor, Xiaomi, and OPO can normally receive the push of alarm information, but other mobile phones do not support it;5. Installation and wiring, note: the separate red wire is connected to the 12V positive pole, and the separate white wire is connected to ON (ACC) on the alarm host. If this line is not connected, the driving cannot be recorded.6. There is no formal record, or the is disordered. Need to connect the white line, connect it to ACC/ON, it can display normally.