JJC Canon Camera Remote Control Shutter Radio Wireless RS-60E3 for EOS R10 R8 R7 R6 Mark II RP Ra R M5 M6 850D 800D 760D 750D 700D 650D 600D 550D 500D 200D II 100D 250D 90D 80D 77D 70D 60Da 60D 1500D 1300D 1100D 1000D G1X III

【Compatible with】
- Canon EOS R10, R8, R7, R6 Mark II, R6, R, RP, Ra
- Canon M6 Mark II, M6, M5
- Canon EOS 60D, 60Da, 70D, 77D, 80D, 90D
- Canon EOS 100D, 200D, 200D II, 350D, 450D, 500D, 550D, 600D, 650D, 700D, 750D, 760D, 800D, 850D
- Canon EOS 1000D, 1100D, 1200D, 1300D, 1500D
- Canon EOS 7, 7s, 30, 33, 50, 50E, 55, 3000
- Canon PowerShot G1X, G1X MarkII, G1X Mark III, G10, G11, G12, G3X, G5X, SX50 HS, SX60 HS, SX70 HS
- Pentax 645D, 645Z, K-1, K-1II, K-3, K-3II, K-30, K-5, K-5IIs, K-50, K-7
* Replaces Canon RS-60E3, Pentax CS-205
【Product Highlights】
1. Compatible with different brands of cameras by replacing the JJC connecting cable
2. 16 available channels
3. Can trigger the shutter from 30 meters away
4. Support single shot, 5 seconds delay shot, 3 continuous shots, unlimited continuous shots and bulb shot
5. Transmitter can fire multiple receivers
6. Receiver itself acts as a cable switch
【How to use】
1. Install the CR-2 to the receiver and 23A to the transmitter. (Make sure to remove the plastic protective paper on the before installation)
2. Set the receiver and transmitter to the same channel (Normally the channel is already matched when you receive the package, so actually you don''t need to set it, but it you ever reset the channel, make sure they are the same)
3. Once the batteries are properly installed and the channels are matched, when you press the shutter on on the transmitter, both the LED bulb on the transmitter and receiver will light up.(If not, please check if the is installed correctly or the is dead)
4. Once the transmitter matches the receiver, connect the receiver to the camera via the camera connecting cable which is included in the package,then set the transmitter into the working mode you want and finally press the shutter on to take a photo wirelessly.
【Package Contents】
- JM II transmitter x 1
- JM II receiver x 1
- CR-2 x 1
- 23A x 1
- Connecting cord x 1
- This manual instruction x 1
JJC JM-II series Radio Frequency Wireless Shutter is designed for most DSLR and SLR cameras that have a remote socket on the camera body. The system works at 433MHZ frequency and has 16 available channels. What’s more, this wireless remote system allows the transmitter to trigger the receiver from 30 meters away. The JM-II receiver simply attaches to a compatible camera''s accessory shoe, and then just connects the supplied JJC receiver cable to the camera''s remote socket. The receiver is powered by one piece of CR-2 lithium while the transmitter is powered by one piece of 23A . JM-II transmitter can trigger the camera shutter at five modes: single shot, 5 seconds delay shot, 3 continuous shots, unlimited continuous shots and bulb shot. The receiver has a 1/4"-20 tripod mount socket on the bottom, so you can even mount the receiver onto a tripod. Most importantly, our JM-II transmitter is able to fire multiple receivers at the same time. The receiver itself with the connecting cable can be used as a Wired Remote Switch, then half press to focus, full press to take a photo. All these features make it good for eliminating camera shake in exposure photography.
JJC RS-60E3 Radio Wireless Remote Control Camera Shutter Release for Canon EOS R10 R7 R6 Mark II RP Ra R M5 M6 Mark II 850D 800D 760D 750D 700D 650D 600D 550D 500D 200D II 100D 90D 80D 77D 70D 60Da 60D 1500D 1300D 1200D 1100D 1000D G1X Mark III II G5X SX70 HS