Wireless Remote Control Switch DC 12V 10A Relay 1CH RF with RF Relay Module for Garage Door Opener

There are two types of individual duplicators, learning type and type 1. Please note that the learning remote control cannot the code of remote controls and can only be used together with the controller module. 2. type can only the code of the remote control, the remote control must be intact Please pay attention to the selection Description： Material: Plastic. Color: As pictures show. Type: Wireless remote. For: Such as electric telescopic door remote control, road gate remote control, alarm remote control and so on. Rated voltage: 12V (included). Wireless transmission distance: 50-150 (m). (open space)

Features Multi-functional and multi-variable, personalized and user-friendly simple design and fast to use. This smart remote control is suitable for electric door remote control, telescopic door remote control, garage door remote control. Cloning types: 2260(PT2260,SC2260,LX2260,HX2260); 2262,(PT2262,SC2262,LX2262,HS2262,HX2262),PT2264,PT2240(LX2240),1527( EV1527,HS1527,HX1527 ),FP527,CS5211,SMC918,SMC926,AX5026,AX5326-3,AX5326-4,HT600,HT680,HT6207,HT6010,HT6012,HT6013,HT6014,HT12D, HT46F49E, PIC16F629,PIC16F630 and so on. Different manufacturers have different prefixes model, as long as the digital portion of the can be the same model. Note: We usually do not recommend copying a rolling code chip, because there are many uncertainties when copying a rolling code chip. When copying a rolling code remote control, it is not possible to determine whether the remote control is an encryption chip. Therefore, we do not recommend copying the rolling code remote control.

Use steps: 1. Clear code: two fingers at the same time hold the unlock key and lock key; the LED rapidly flashes 3 times in about 2 seconds; let one of the fingers go (the hand cannot let go), and then use the loose finger to quickly click three times on the loose button until the LED flashes quickly; the two fingers can release; then press any one key of the remote control; when LED goes off, it means clear code is successful(four keys all empty); if after you press any button of the remote control, the is still on, it indicates that the code has not been cleared successfully. You need to re-clear, and only successfully clearing the code can cloning be successful. You can repeatedly clear and clone the code. 2. : left hand taking the remote control, right hand taking our cloned remote control and keep two remote control as close as possible; press the first keys of two remote controls at the same time; in about 2 seconds, the LED will flash quickly 2 times; after one second, the indicator keeps flashing and let go of your fingers; and then press the key after successful study, the keeps on, which means that the first key code on remote control has been copied to the remote control; the same method can be used in turn on the second key, the third key... If the is successful, the remote control function is the same as the matching remote control. 3. Restore: When you accidentally clear the of the remote control code, you can simultaneously press the of the remote control of the bottom two keys, LED lights will flash quickly, let go after pressing any key, long, this Indicating that the code for the remote control is restored. Before using our remote control, please be sure to remove the existing code from the remote control. 4. How to deal with the situation where some of the keys can control, the rest cannot control? You can use clear and restore operation, the specific operation is as follows: (1) first clear code; (2) after clearing code, the unsuccessful key again, and there is no need to the rest buttons; (3) and then clear the code again; (4) restore code; at this time, the keys that were not successfully copied are now covered by new codes, and the keys that were successfully copied are now retained. If there is no after the second of the keys, repeat the above steps again and again until all keys are successfully copied.

Precautions: 1. Select the remote control of the prerequisite: the remote control function is normal, the remote control is the same or compatible, remote control operating frequency the same. 2. The remote control can only the fixed code, learn the code and part of the single-chip remote control (can the model see copyable type). 3. Two-way remote control, rolling code remote control, single-chip encryption program remote control cannot be copied. Such as HCS200, HCS201, HCS300, HCS301 and so on. 4. Before copying the remote control, make sure that the existing code on the remote control has been cleared and check that the code is cleared successfully. Otherwise, it cannot be copied. 5. Please ensure that your remote control has enough power, the distance between the two remote control the better! If the distance is too close to the switch at different angles to . Press and hold the button on the remote control to send the completely normal, and then press the button on the remote control to ensure that the function is completely copied. Notes: 1. Please allow 1-3mm differs due to manual measurement. 2. Due to the different display and different , the picture may not show the actual color of the item. Thanks for your understanding. Package included: 1 * 433MHZ remote control duplicator. 1* Module
---------------------------------------------------------------------------【Version 2】---------------------------------------------------------------------------
• Input Voltage: 12 V
• RF working mode: Superheterodyne
• sensitivity: > 97 dbm
• Transmitting distance:> 100 m ( open space)
• Decoding mode: MCU software decoding
• Remote storage: 20
• Support remote type: EV1527 learning code
• Working mode: Momentary, toggle, latching time delay (5s, 10s, 15s )
• Output terminal: NO, NC, COM
• Dimension of :35 x 30 x 18 mm (L,W,H)
• Remote control : 2 x 3 V CR2016 button
Note: Maximum input power is 250 V

Remote programming
-Clearing the code :
Push the learning button on the 8 times, the codes will be reset.
After clearing the code, remotes will need to be recalibrated

-Momentary mode
Please contact for detailed use instructions

-Learning the code:( Toggle - Press remote button to turn on, press again to turn off.)
Press the learning key on the 2 times, Wait for a moment, the LED will be off, it comes into learning state.

-Push the learning key on the 3 times, the LED (on the )will blink 3 times.
When the LED is on, press the button of the remote control (You want to let it learn), Push the remote button A, LED flash for 3 times.
Push the remote button B, Led flash for 3 times.
After 3 seconds, the LED indicator will be off, Learning to succeed.

Package including
1 * module
1 * Remote Control(with )
Note: This item comes without a box, but please rest assured that we will pack it well before shipping!