W2026C Digital humidity Moisture meter DC 12V Hygrometer Humidity Controller Detector 0~99%RH Adjustable w/ Humidity sensor

Product parameters

Product model: ZFX-W2062C

Product Name: Intelligent high precision digital humidity controller

Control humidity range: 1%RH-99%RH

Load power: 10A/DC12V/24V

Humidity measurement range: 1% RH-999% RH measurement error:

±3% RH (good environment temperature is 25℃)

Control humidity accuracy: 1% RH display: 1% RH

Humidity return: adjustable between 1-50% RH

Supply voltage: DC12V/24v

Output type: 10A relay output

Probe type: humidity resistance sensor

Size: 48*29*22mm (long * section * high)

Installation hole: 46*27m

Moisture control object: dehumidification or humidification

Probe line length: 1.5m line length

Working environment: humidity 90% RH no frosting

Parameter code and settings

Code

Descrtion

range

Factory settings

P0

Humidification/dehumidification

H/C

C

P1

Backlash

1-50%RH

P2

Set the maximum limit

99

95

P3

Set the minimum limit

1

5

P4

Temperature correction

-10

10

P5

Delayed start

0-10

1

P6

Restore Factory settings

ON- OFF

OFF

Setting instructions

Connect the power supply and load to power the controller. The red color above shows the humidity, blue below.

Also red) is displayed as the desired humidity, and pre STG (+) ENT (-) to set the required humidity

After the setting is completed, wait for 3 seconds to automatically confirm the return. At this time, the controller automatically performs relay energization according to the setting.

For 10A relays, to meet high power loads, please make sure the line is correct.

Indicator light, digital tube status descrtion

Indicator light: off means the relay is off, steady light means the relay is closed

Digital tube: The above shows that LL is the sensor open circuit, indicating that HH is out of the measurement range, the humidity will forcibly open the relay.

Display - for ultra high humidity protection.

Parameter function descrtion

Pre and hold SET for 5 seconds to enter the main menu settings, pre SET (+) ENT (-) to switch P0-P8, when adjusting parameters P0-P8 parameters

If you need to adjust P0, pre SET on (+) ENT (-) at the same time, adjust 0K, then control SET (+) ENT (-)

Once confirmed, P1-P8 and P0 set the parameters in each code according to their own needs.

Panel settings:

Wiring diagram:

More Products Please Click Below:

Category List

For DiY For Raspberry Pi Wirele Module Step UP/Down Module

ESP8266 Series CH340 Series Relay Switch Tools Temperature Controller

Voltmeter Ammeter USB Tester LED/LCD Modules Sensor Converter & Regulator

DC/AC/Stepper Motor Signal Gengerator Development Expansion Board

About shping
Shping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.