V3 1.2 - 12V ZB2L3 18650 Li-ion Lithium Battery Capacity Meter Discharge

V3 1.2-12V ZB2L3 18650 Li-ion Lithium Battery Capacity Tester Resistance Battery Capacity Meter Discharge Tester

Basic parameters:

Power supply voltage: DC4.5-6V (micro USB interface)

Working current: no more than 70mA

Discharge voltage: 1.00V-15.00V resolution 0.01V

Termination voltage range: 0.5-13.0V

Support current: no more than 3.000A resolution 0.001A

Voltage measurement error: le than 1% + 0.02V

Current measurement error: le than 1.2% + -0.002A

Test data range: 999.9Ah (Ah, 1Ah=1000mAh) or 9999Min (minutes) when the value is large, switch by decimal point shift, when it is lower than 10Ah, it is displayed as X.XXX, and above 10Ah, it is displayed as XX.XX, This type of push.

Finished product size: 54mmX41mmX17mm (length X width X height)

Package includes: Lithium Battery Capacity Tester (including line)

ZB2L3 Battery Tester LED Digital Display 18650 Lithium Battery Power Supply Test Resistance Lead-acid Capacity Discharge Meter

Descrtion:

100% brand new and high quality

Material: Electrical components

Color: See pictures

HW-586 battery capacity tester discharge type 1.2-12V external load capacity of the battery and other tests 18650

Tools, single-function, by controlling the load off and get real-time integrated discharge current capacity results

Maximum support 15V 3A discharged through the discharge voltage and current, itself does not discharge

Maximum capacity statistics support 9999Ah (9999000mAh)

Automatically identify and develop appropriate battery termination voltage can also be manually adjusted

Specifications:

Power supply voltage: DC4.5-6V (micro USB connector)

Operating Current: le than 70mA

Discharge voltage: 1.00V-15.00V 0.01V resolution

Termination voltage range: 0.5-11.0V

Supported by current: 3.000A 0.001A resolution

Maximum voltage measurement error: 1% + 0.02V

Maximum current measurement error: 1.5% + - 0.008A

Maximum battery capacity range: 9999Ah (1Ah = 1000mAh) greater value by shifting the decimal point to switch, when the display is le than 10Ah X.XXX, as shown above to achieve 10Ah XX.XX, and so on.

Board size: 50mmX37mm

Finished Size: 50mmX37mmX17mm (length X width X height maximum position size, contains copper foot height)

Instructions:

1. The first test should be fully charged battery.

2. Connect the battery to be tested positive to positive input, a negative input to the negative, can not be reversed (with load reversal may damage the circuit)! Load connected to the output of the positive and negative output, to work through the tester micro USB power supply (not available desktop or laptop USB powered), then the battery voltage.

3. Direct start test need only one pre of the "OK" on, the tester can automatically develop an appropriate termination voltage of the battery full charge voltage, and will start flashing after the test three times. Need to develop artificial termination voltage only when the battery voltage display state by preing "+" or "-" ons to modify the termination voltage display beginning with P, behind the representative voltage resolution 0.1V, set up after preing the "OK "start testing.

4. After the start of the test the tester will control the load of the electronic switch is turned on, the test data shows that the proce will release capacity (Ah), current discharge current (A) and battery voltage (V) between the wheel was. When the battery voltage reaches the set cut-off voltage, load control switches off the tester display data stays in capacity (Ah) and above and the corresponding indicator flashes quickly together, now displays the actual capacity of the battery is discharging capacity, about the pre "OK" to terminate flashing allows stable data display, pre again "OK" on to return to the power-on state can just replace the battery test the next section ......

Error codes and their meanings:

Err1: battery voltage is above 15V

Err2: battery voltage is lower than the termination voltage

Err3: Battery can not afford to load or discharge current line too much resistance

Err4: overcurrent (current exceeds 3.1A)

Note:

Use the resistance of the discharge proce, resistive load will seriously heat, please pay attention to safety!

This circuit voltage in order to improve the measurement accuracy, specially designed DC bias, when the terminal displays nothing then a small voltage does not affect the actual measurement, if you are shorting the input terminals (absolute 0V) will show 0

No retail package

Quantity:1Pc

Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!!

Package Included:

1Pc x battery capacity tester

2Pc x Load resistors

About shping
Shping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.