Upgraded 110W 30V Constant Current Electronic Load CC Discharge Battery

110W 30V Constant Current Electronic Load CC Discharge Battery Capacity Tester 0.10-9.99A 0.9-28.0V brand new and high quality Material: Electrical components Color: See pictures New Upgrade: 1. The test current range is changed from 0.20-9.99A to 0.10-9.99A. 2. The lower limit and termination voltage range is changed from 1.0-25.0V to 0.9-28.0V. 3. Support non-operational voltage display. 4. Increase the support for four-wire test in electronic load mode, with independent four-wire voltage indicator. 5. The LED indication setting digit is changed to the current setting digit flashing indication. Features: Cause sterility new New design , simple and versatile electronic load ! Automatic memory function with all parameters , is well suited for automated aembly of the power adapter aging cabinet In the of the latest version , slightly larger size and upgrade the fan into the 5020 Delta high speed dual bearing fan , higher cooling redundancy , more suitable for long hours ! Note: This product is a profeional testing equment , requiring the user must have some basic electronic ( example: Users should understand what is the meaning of the voltage and current capacity Ah , etc. ) , or you may be unable to properly use the device , poibly mishandled cause unneceary damage caused by the test device lo ! PPower supply requirement : DC12V voltage ( actual voltage 11-14V) current is not le than 0.5A of power, the power will be displayed inappropriate Err6 Note: The default power adapter is not included Specifications: Operating modes: single mode constant current (CC) Discharge current : 0.10-9.99A ster 0.1A or0.01A Discharge current maximum error : 0.7% -0.01A The maximum capacity test error : 0.5A 2.5%, 2A 1.5%, 5A and above 1.2% Offline ( termination ) Voltage Range : 0.9-28.0V. sting 1V or 0.1V Discharge voltage : 1.00-30.00V The maximum voltage measurement error : 1% + - 0.02V it can open 9.99A 6V and 20V maximum at the only open 3.00A) Highest battery test statistic : 999.9Ah or 9999Wh, achieve value stop testing ( first value to those who stop condition )) Board size : 60W 100mm * 70mm * 57mm ( fan prominent board about 12mm) Positioning hole locations : 60mm * 88mm diameter 3.2mm 5mm pedestal already installed Fan control : intelligent fan control ( according to the radiator fan can be infinitely variable automatic temperature ) Protection: Overheat protection "otP", transient overpower protection "oPP", overpreure protection "ouP", reverse polarity protection, power supply voltage abnormal protection . Instructions:: A : mode settings ( default factory for electronic load mode ) : Hold down the start-stop on ( red on ) to the tester simultaneously energized until the key is released showing Fun * When , by rotating the knob to change the setting , "Fun1" for electronic load mode , "Fun2" battery capacity test mode. Push on start and stop at the after entering the settings, also set "bEon" by turning the knob to open or "bEoF" closes After setting pre the on again to start and stop at the tester restart. Setting Digital Illustration: II: Electronic Load mode: 1. Turn on the power supply 12V boot into electronic load mode , ensuring in a stopped state ("RUN" does not light, otherwise the pre of the start-stop switch to turn off the load ) connected to the power supply under test to the test port input power (P + P - ) , pay attention not to take the wrong polarity ! 2. Set current and lower voltage knob , turn the knob to set the value of the current setting position , then pre the knob to change the setting digit, digital middle two digits to the right of the indicator and digital indicator VA simultaneously determine the current set position . 3. Pre the start-stop switch , load began to run , "RUN" lights , power is applied to the circuit under test is set to enter the discharge current , while the upper display the actual input load voltage , when the voltage drops below the set limit voltage " RUN " LED flashes and short beep alarm accompanied. 4. The test procedure can be modified at any current , and if you need to modify the lower voltage to stop the load can modify . Note:When in alarm state , can only transfer a small current does not increase !Tester automatic power-down feature to save enough to save the set parameters and run state, when the state again after power transmiion will complete before the power fai and restore data. 3: The battery capacity test mode: 1. The test battery should be fully charged with a special charger ! 2. Give the tester is powered into the battery capacity test mode, connect the battery current line to P + P- positive and negative terminals , if you use four-wire clamp test, while the four-wire interface to the positive and negative voltage test fixture is connected to V + V - port. 3. Turn the knob to set the discharge current and discharge voltage ( referring to two specific methods : 2 Descrtion ) , one pre after setting the start and stop switch , a battery tester and a first line detection, automatic identification 2-4 line ( 2-wire line identification presentation JS-2,4 identification JS 4, if an error please stop the test and check the wiring ) , then enter the test , if the fault code appears , refer to later explain . The testing proce will round up digital noticeable battery voltage , current , and the current discharge capacity Ah discharge energy Wh, when the discharge end ( battery voltage is below the set voltage ) , the tester displays the data stays in Ah and b-link rapidly , with bee shortne alarm. 5. Pre the start and stop at the knob or switch to stop the alarm , you can turn the knob to view the battery discharge data , including discharge capacity Ah, Wh and discharge energy platform voltage V, start-stop on is preed again , clear the data back to the initial setting interface before testing the next section batteries. Additional information: 1. Battery test proce can adjust the discharge current , if you need to re- adjust the termination voltage , you can pause by preing the switch at the start and stop the discharge modification ( pause discharge will return to the settings page , this time discharge data is not lost , if neceary , you can long pre clears the data until the start-stop switch 0.000Ah). 2. Tester automatic storage can record setting parameters , and record all parameters and status at the end of the test proce and test power fai alarm status , re- transmiion of all automatically restored. Fault protection codes and meanings : Err1: ultra-high capacity test the battery voltage . Err2: battery voltage is below the set termination voltage is not connected to the battery or the battery is reversed . Err3: line resistance is too large or the battery can not afford to set the discharge current. Err4: circuit fai . Err6: working power is inappropriate , use a standard 12V power supply , and the supply current is not le than 0.5A. otP: overheating protection. Ert: temperature r fai or the temperature is too low. ouP: ultra-high voltage electron -load mode . oPP: under ultra-high power electronic load mode instantly . No retail package Quantity:1Pc Note: Due to the difference between different monitors, the picture may not reflect the actual colorof the item. Thank you!! Package included: 1 * Electronic Load Battery Capacity Tester About shping
Shping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.