Universal Car Alarm System e Control Central Door Lock Locking Wireless

Specification:Material: ABSProduct size: 98*34*10mm/3.85*1.33*0.39''Rated voltage: 12 (V)Rated current: 10 (mA)Installation mode: wireleCorresponding frequency: 315MHZ,433MHZModulation mode: ASKWirele transmiion distance: 50-100m (open space)Application: garage door, alarm, automatic door, rolling door, etcType of copied ch: 2260 (e.g. PT2260, SC2260, LX2260,HX2260); 2262, (such as PT2262, SC2262, LX2262,HS2262,HX2262, etc.), PT2264, PT2240 (LX2240), 1527(such as EV1527, HS1527, HX1527), FP527, CS5211, SMC918, SMC926, AX5026, ax5326-3, ax5326-4, HT600, HT680, HT6207, HT6010, HT6012, HT6013, HT6014, HT12D, HT46F49E, PIC16F629, PIC16F630, etc., can also copy other types of chs compatible with the above mentioned chs. Different ch manufacturers will have different prefix ch model, as long as the ch model numberPartof the same can be copiedNote: We generally do not recommend copying roll code ch, because there is a lot of uncertainty when copying roll code ch. When copying roll code ch e control, we cannot determine whether the e control ch is an encryption ch or not, and we do not recommend copying roll code e control with a pair of e control.Operation Manual:1. Clean code: shut at the same time hold the lock with two keys (some of the shell are the two key) upward and downward, theLEDindicator lights flashing three times, pre release any one of the key, another is not loose, click the release on three times, rapid flashingLEDlight into the state, at this time of memory data all cleared, after cleaning the data of the e control, pre any key, theLEDindicator is on.2. Copy: One hand-held e controller, the other hand-held copy e controller, two e controllers as close as poible, (ideally two e controllers zero distance side by side on the desktop) respectively pre the required copy ons,LEDindicator flickers quickly after three flickers, copy succe, other key operation method is the same. Some e controllers have low transmitting power, so they should be equped with e controllers and back-to-back operation of copying e controllers to cope well. If there is interference in some operating environments, interference operation should be avoided. If copying is not good, copying should be done again after code clearance.3. Recovery: When you inadvertently clear the code of the copying e controller, you can pre the bottom two keys of the copying e controller at the same time. After three flashes of theLEDlamp, it will flicker quickly. After release, you pre any key again and the light is long, which indicates that the code of the copying e controller has been restored. Before using our copy e control to copy, please make sure to clear the existing code of the copy e control first.4. How to control some of the keys after copying, and the rest can not be controlLED, you can use the ts of cleaning and restoring operation, the specific operation is as follows:(1) Clearing the code first.(2) Copy the keys that have not been copied succefully again after the succeful code clearance, and do not copy the keys that have been copied succefully before.(3) Clearing the code again.(4) Make a restore operation once; at this time, the key that had not been succefully copied was covered by the new copy code, while the copy of the succeful code was retained. If there are still keys that have not been copied succefully after the second copy, they can be coded again, and the keys that have not been copied succefully can be copied again, and then coded and restored again. This is repeated until all keys are succefully copied. This little trick can be used to reduce the hale of repetitive operations.Warm Ts:1. Prerequisites for selecting the duplicate e controller: the e controller has normal function, the e control ch is the same or compatible, and the e control work frequency is the same.2. The copying e controller can only copy fixed code, learning code ch and e controller of some single ch computers (the type of ch that can be copied is shown in the descrtion of the type of ch that can be copied).3. Two-way e controller, scroll code e controller and single-ch encryption program e controller can not be copied. Such as HCS200, HCS201, HCS300, HCS301, etc.4. Before copying the e controller, make sure that the existing code of the e controller has been cleared and check whether the code has been cleared succefully. Otherwise, replication is not poible.5. Make sure your e controller has enough power when copying. The closer the two e controllers are, the better. If the copy distance is too close, the switch can copy from different angles. Preing the on of the e control requires that the transmitting signal be completely normal, and then pre the on of the duplicate e control to ensure that the function is completely duplicated.Note:Please allow 1-3mm differs due to manual measurement.Due to the different display and different light, the picture may not show the actual color of the item. Thanks for your understanding.

1 X Cloning e Control

Drop Shping Service.1.There is no limited stock to fulfill the orders on a daily basis.2.For USA/CA /RU the shping speed is very fast.3.Priority delivery,fast delivery in 48 hours.4.No invoice or rece or promotional materials included.5.Support CSV/EXCEL ( larger orders) dropshping.

About shping
Shping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.