Universal 12V Car Battery smart protector with 2 Isolator Master prevent loss

Attention please:

Can't be fitted to cars with extra alarm battery. Such : Voo XC90 V8 2007

1.Universal 12V Car Battery smart protector with 2 e controllers Cut Off Isolator Master prevent battery lo running out Switch Wirele e Control Disconnect.

2.The BPM-12electric paralysis protector is an intelligent electronic device installed on the battery. Monitor the electric quantity and charge and discharge state in real time while working. When the battery is about to run out of electricity, the battery will be disconnected in time in order to retain the minimum electricity needed for the next start-up, and to protect the battery from exceive discharge.

3.The equment is connected between the electric bottom and the negative number of equment by this method. It is often used for battery protection, RV double battery isolation protection, motorcycle electric protection, computer room spare battery protection and so on.

Specifications:

Working voltage: 12V

Standby current ≤ 1.5mA

Through current: 120a

Instantaneous current: 1200A

Suitable for vehicle type: vehicles with displacement ≤ 4.0

e control:320ft/2Pcs，1PCS Adapter，4PCS Nylon rolled str

Product characteristics:

1.Non-contact switch control to completely eliminate dust and water vapor entry

2.e control

3. OLED screen display voltage, power, on-off,intuitively visible, visual settings.

4. LED working status display

5. Power saving design, standby orbital mode as low as 400 microamperes, an average working current of 1.5 Ma, to provide 180 days of parking protection

6. 16 square pure copper flame retant specification, supporting super large start-up current.

7. Pure thickening manual switch, easy to install, and provide convenient and fast manual turn-on mode.

8. 120A self-locking on-off controller, supporting short-term 1200A start-up current, standby zero power consumption.

9.Special circuit design, support input and output installation at will, support positive and negative pole installation at will.

10. Full sealing + sealing + EVA sealing proce, providing 68 grade (highest grade) protection standard.

11.ary grade devices, built-in hardware watchdog, to ensure stable operation.

12. Disaster safety design, even in the case of the maximum fai of the ch and its surrounding circuits, the self-locking characteristics of the on-off controller can still maintain its normal turn-on and ensure the safety of driving.

Method of use:

1. The equment boot display screen is turned on, showing the product model and version, and entering the main interface after 2 seconds;

2. The main interface has four thin display content:

84%: remaining battery capacity

12.63v: real-time bottom voltage

50%: disconnect power setting

When the real-time power is lower than the disconnected power and the well lasts longer than the set disconnect time, the equment will cut off the power supply

Sm: devices work in enhanced security mode (no display indicates regular protection mode)

On：on and off status of device

On- connected. 0ff- Disconnect, Time to zero and disconnect immediately.

3. Key OFF/-:

When the screen goes out in standby state, click wake up screen display

In the bright screen state, click will perform the shutdown action, disconnect the battery from the electrical equment: in setting mode, click to perform digital suraction operation, see the setup wizard for details.

4. Key ON/+:

When the screen goes out in standby state, click on the wake-up screen to display

When the screen state, click will perform the opening action, connect the battery to power the device; in setting mode, click to perform digital plus operation, see the setup wizard.

5. e Controller:

OFF- disconnects battery from electrical equment

ON- turns on battery to power equment

6. LED: red light flashes to disconnect and green light flashes to turn on.

The red light flashes once in 1 second, indicating manual or e disconnection.

The red light flashes once in 2 seconds, indicating that the equment is automatically disconnected and that the remaining battery power is sufficient. The red light flashes once in 5 seconds, indicating that the power has been exhausted and must be charged immediately.

The green light flashes once a second, indicating that the bottom capacity is sufficient.

green light flash quickly, indicating that the remaining power is below the set value, disconnect countdown,

Special reminder:

A: When OFF is set up in safe running mode, there is no limit to the new opening, and disconnection is performed unconditionally whenever an instruction is received.

B. The safe operation mode is set to ON, at a real-time voltage Above 13.2v(The system thinks that the engine is running and the generator is generating normally). The equment will not accurately respond to any disconnect instructions to ensure driving safety with maximum procedures (see the section on setting up wizard safety town switches for details).

Setup wizard :

1. Touch and hold down the ON/+ key for more than 2 seconds, click OFF at this time , screen shows that the SET MODE, is immediately loose Turn on the on and the device enters setup mode.

2. Protection voltage: sets the disconnect voltage

Default 12.2v. The estimated residual capacity was 53%.

Pre +/- to add or suract settings.

Pre the ON/+ key long after completion to enter the next setting.

3. Disconnect delay: sets the break delay

Default 300 seconds, when the battery voltage continues to fall below the set value

After 300 seconds, the equment automatically disconnects the whole car.

In order to prevent frequent on-off, when the voltage is higher than 13.2v in the delay proce, the delay will stop and return to the normal monitoring state.

Pre +/- to add or suract setting

Pre the ON/+ key long after completion to enter the next setting.

4.Safe mode setting: safe mode switch

Turn on ON, by default for higher security.

When set to ON:

①. When the battery voltage is higher than 13.2V, the device is absolutely not allowed to disconnect, whether it is keystroke or e control, as well as automatic, do not allow disconnection:

②. No matter how (automatic, keystroke or e control) is disconnected, when the voltage returns to more than 13.2v, the equment will be automatically turned on to ensure that the battery will be replenished in time.)

Pre + /- add or suract settings.

Pre the ON/+ key long after completion to enter the next setting.

5. Save settings

Pre + /- to select yes/no, to determine whether the device is saved

Parameter, and then restart into working mode

Note: at any time in the 3.4.5 steps above, you can long pre OFF to cancel the setting, and the device abandons the set parameters and exits the setting mode.

Wiring instructions:

Fix one end of the adapter to the positive or negative pole head of the battery, the positive or negative power line of the vehicle to the other end of the adapter, fix the two wires of the host to both ends of the adapter, and connect the yellow wire of the host to the other electrode of the battery.

About shping
Shping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.