Type-C PD QC AFC Fast Charge Decoy Trigger Module DC 5V 9V 12V 15V 20V Output for Charger WIFI Router Output Charger Board

Explain:

D switch selects voltage output module (type A):

1. Fast charging support protocol: PD2.0/PD3.0.QC2.0/QC3.0.AFC.FCP

2. Module support voltage: 5V/9V/12V/15V/20V (charger support required)

3. Voltage regulation mode: according to the table behind the board, adjust the dial switch to control the voltage output

Note:

1 After adjusting the dial switch, because there is no voltage indication, it is recommended to use a multimeter to measure the voltage before connecting the application circuit

2 If the dial switch is not adjusted according to the table, the module will output the voltage supported by a module at will

3 Whether these voltages can be output (5V 9V 12V 15V 20V) depends on your charger.

Size: 30mm X 20mm X 10mm

Weight: 3g (standard), 4.6g (with terminal), 4.4g (with USB)

Voltage output selection on module (QCTC20TB):

Introduction:

1. Fast charging support protocol: support PD3 0. PD2. 0. QC, FCP, AFC voltage bait output, mode free switching can also be set, only PD is supported.

2. Support 5V/9V/12V/15V/20V bait output (the specific range depends on your power supply).

3. It has key locking function to prevent misoperation (to avoid damaging load equment by setting voltage incorrectly).

4.5V/9V/12V/15V/20V quick setting. LED indicates output.

5. The parameters are saved automatically, and the last spoofing setting is executed after power on.

6. Ultra low power consumption, high current, supporting 100W output.

7. Maximum 20V/2A output (actual value depends on your power supply).

8. Type-C is integrated and durable.

9. It is applicable to aging test, and the module withstand voltage is above 30V.

10. Each voltage can be quickly switched by external key

Explain:

1. PD short circuit only: After short circuit, the module only supports PD protocol.

2. DM and DP short circuit contacts: DM and DP can be output from USB after short circuit. Short circuits are not recommended unle neceary.

3.5 Short contact of independent keys: five independent keys can be connected to quickly switch the voltage, which can be short circuit, short pre, long pre (the five short contacts on the module circuit are grounded together).

4. S1 short contact: this is the key locking function. After the short circuit, the switch voltage needs to be . The unlocking method is to pre and hold the key to start the machine. To restart, you need to unlock again.

Matters needing attention:

1. The power supply must support PD or QC protocols.

2. Before use, please confirm whether the output voltage is consistent with the power consumption voltage of the electrical equment used, so as to avoid burning the equment by misoperation, or you will be responsible for the consequences.

3. Try to hold the edge of the board with your hands and do not touch the ch directly to avoid damage to the ch by human static electricity.

4. When the decoy output voltage setting is unknown, do not connect the load first, and then connect it after confirmation to avoid the voltage exceeding the withstand voltage of the load.

5. The reason for voltage jump (the indicator lamp flashes): If the no-load output of the decoy is normal, there is a load voltage jump (the voltage has just risen back to 5V or is simply disconnected). In this case, the load power exceeds the power that the power supply can provide. At this time, the power supply will be forced to perform voltage reduction or power fai protection. At this time, only a higher power supply can be replaced or the load power can be reduced.

Size: 40.57 x 20.32 X 10mm

Weight: 4.4g (standard), 6.5g (with terminal), 6g (with USB)

Detailed list

1 * Type-C PD QC AFC fast charging bait trigger module DC 5V 9V 12V 15V 20V output charger module

About shping
Shping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.