Solar Powered Animal Waterproof PIR Sensor Outdoor Garden Anti Cat Dog USB Ultrasonics Solar Alarm Drive

3-in-1, Ultrasonic + Strong Light + 120bB Burglar Alarm. Solar Built-in Ni-MH . Weather-proofto work all year-round in all weather conditions . Once Installation forpermanent service! INTSRUCTION: 1.“ON”mode: Ultrasonic+ Strong Light The Passive Infrared Sensor（PIR) detects motion and triggers the ultrasonic speaker emitting a tone that people cannot hear but chases away common outdoor pests like dogs,cats,deer,raccoons,mice, skunks,squirrels and more. Also start the flash . 2.“ALARM”mode:Ultrasonic+ Strong Light + 120bB Burglar Alarm Infrared sensing head detects moving objects and triggers 120 dB alarm sound and ultrasonic sound and strong light at the same time to repeldangerous animalsor evildoer. 3.“OFF”mode: For turn off the Specifications: Size:14x11.1x8.7cm (Stand: 32cm) Weight:430G Mode:Built-n 4x2/3AA Ni-MH rechargeable Batteries. Consumption(Working): 15mA Consumption(Standby):≤10uA Ultrasonic Frequency: 25-61KHZ Alarm Sound: 120dB Coverage Area: 8m / 30ft ASSEMBLING: 1.Unpack it and confirm that if all parts are present. 2.It`sdesigned forcontinuoususe, with built-in2/3AA size NI-MH rechargeablebabatteries 3.Once turned ON, the red-LED light and ultrasonic signal will activate for 15 seconds. Among the time , there is sound waves for 2.5 seconds at the beginning. At the same time , the white-LED lights flash . Following this activation,the unit will go to stand-by mode. 4.The location should allow adequate sunlight to keep the batteries fully charged.And makesurethatit`s within the effective range of the . 5.For best results, please keep the head roughly9-10 inches above ground. 6.Take carenot to stress or the when installing in hard ground. It is a good idea to prepare the ground for the ground stake to avoid damage to the unit. 7.When the PIR sensor detects motion, red-LED light will be on, The ultrasonic signal and the white-LED lights will run for 15 seconds. Following this, the will return to stand-by mode. 8.When the device is working and the PIR sensor detects motion, the Device will run for 15 seconds in the time. CAUTION: ? Check for underground utilitieslikecables or wires before digging or installingto preventpersonal injury, property damage or even death. ?Allow the ALARM to operate continuously for best results. ?Do not immerse in water. ?Do not cover-up the PIR sensor. ?To clean the , use a damp- cloth and mild soap with Water. Do not use harsh chemicals or cleaning agentsThat may damage the .
















a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a