RF 433.92Mhz Universal Wireless e Control 433 Mhz Switch 110V 220V 10A Relay Mini Receiver e Control for Gate LED Ligh

RF 433.92Mhz Universal Wireless e Control 433 Mhz Switch 110V 220V 10A Relay Mini Receiver e Control for Gate LED Ligh

Features

• 1:Simple and convenient

Simple wiring, easy to install, complimentary stickers, you can stiit anywhere you want on the wall.

• 2: High quality chip

30 can control one switch at the same time,

One e control can control 30 receivers at the same time.

• 3: Mini Size

Only 75*35*20mm mini size, can be installed in 95% of the devices on the market;

• 4: Control distance

100 meters control distance, meet the requirements of most environments.

• 5: IP44 waterproof e control

The e control has been improved with IP44 waterproof tape. After dropping the e control into water, it can still be used normally when you take it out.

• 6:Good Packing

All the goods will be packed with bubble bags, even if you receive the wall cracked and d, there will be no damage, to ensure that the goods are delivered to you in good condition.

Model Number: KR2201D-4
Input voltage: 220V
Working current: 10A
Maximum load power: 2200W
Frequency: 433Mhz
Support en format: EV1527, PT2262
Working mode: Momentary, Tole, Latching Time delayModel Number : KT05-ONOFF-
Operating Frequency: 433MHz
Power by 3V Coin Cell on Battery Battery included
Material: PVC
on: 2 ons
Size: 59mm x 28mm x 8mm
Operating Voltage: 3V
Operating Current: 12mA
nsmitting Power: 10mw
Modulation Mode: ASK AM
En Type: Learning
nsfers Distance: 20-100mopen space

About Working mode:

Momentary: Press the e on, the relay connects, release the e on, the relay disconnects.
Tole: Press once the e on, the relay connects, press the e on twice, the relay disconnects.
Latching: Press the e on A, the relay connects, press the e on B, the relay disconnect.

Learning the Code:Momentary

Press the learn on on the receiver four times to enter instant setting mode.
Wait for a moment, the LED will be off , it comes into learning state.
Push the e on, LED indicator on the receiver board will f then come off.
After 3 seconds, the LED indicator will be on again, learning successfully.

Learning the Code: Tole

Press the learning key on the receiver twice time, it comes into tole setting mode.
Wait for a moment, the LED will be off , it comes into learning state.
Press the e on, LED indicator on the receiver board will f then come off.
After 3 seconds, the LED indicator will be on again, learning successfully.

Learning the Code: Latching

Note: When you choose for latching mode, in order to learn more e control, you need to learn two different on, the first time learning is for ON, the second time learning for OFF.
For example: on A = ON, on B = OFF
Press the learning key on the receiver tre time, it comes into latching mode .
Wait for a moment, the LED indicator on the receiver board will f then come off.
Press the e on A. LED f for 5 times.
Press the e on B. LED f for 5 times
After 3 seconds, the LED indicator will be on again, learning successfully.
A = ON, B = OFF.

Note：

1. Please do not charged operation, you should shut off the power, and operation after testing and correct electricity.
2. Please promptly change battery when e control voltage is insufficient when the battery voltage is insufficient, generally get close nsmitting.
3. Please pay attention to avoid metal mask,large equipment,strong interference electroic filed when using wireless RF products, and avoid too short distance between the e control and receiver board.
4. Please avoid abnormal using of the product.Abnormal using will reduce product performance and life, when seriously it may damage the products and even e danger for your safe.