Professional Car Door Smart For Electric Tail Gate Accessories Flaps Open Controll Auto Lift Contactless Trunk Boot Kick Sensor

Features: Microwave Sensor: One Kick is a microwave sensor mounted on the inside of the rear and sends down microwaves to detect. Tail Box Control: If the inductor detects an effective kick action in the induction area, it will output the corresponding level signal according to the signal intensity to control the opening of the tail box. Convenient: After installing a kick, the owner can easily open the trunk of the car through the kick action, no longer for the hands of large it and feel inconvenient. Fitment: This product just fit the car with electric tail gate lift. Install: There is the enough space in the rear per for installing our sensor. Specification Material: Plastic, electric compones Color: Black Power supply voltage: DC 5-18 V Starting time: about 2s Operating current: about 5mA Microwave working mode: intermittent Microwave duty cycle: 4.4% Operating temperature :-40-+85 ℃ Emiion frequency: 24.125 0.125 GHz Protection grade: 68 Extension wire connection method 1, black line (power negative) : lapping; 2. Green line (key line) : keep a good contact with one end of the test pen tower iron end and the line on the rear door key socket. Pre the rear door on at this time, and the light of the test pen will be off.(diode "test pen) 3. Red line (positive pole of power supply) : connect the car with 12V constant current; 4. White line (ACC) : keep good contact with one end of the tower iron of the test pen and the other end with the measured line. At this time, the car key is preed to ACC, and the light of the test pen will light up Note: After connecting all wires, wait 20 seconds for self-test and then test again Installation steps and precautions (post-installation) : 1. First, we the position to be installed on the inside of the rear. It is best to install the sensor in the middle of the rear of the car without leaving soil, dust and water 2. Aimed at the hole mark on the sticker and drilled with a screw of your own, noting that the direction is outside the screw cap; 3. When the screw is drilled into the about 1 cm, stop drilling, and place the holes on the left and right sides of the microwave sensor on the screw drilled. The white glue surface is the induction surface, and the induction surface must be downward to the ground 4. Pre and hold the microwave sensor to continue to screw the screw to fix the microwave sensor. After tightening the screw, the white glue and the inside of the should be completely fitted, and there can be no gap in the middle to prevent the sediment from entering and affect the use effect. 5. If there are mesh, protrusion and other structures on the inside of the white glue on the module can not be completely fitted with the inside of the .The mesh, protrusion and other structures must be polished or filled with gla glue, otherwise the gap between the water and sediment will greatly affect the performance of the sensor. Package included: 1pc x Sensor Module 1pc x Probe Signal Cable 2pxs x Location Screws 1pc x Location Paper

FEEDBACK 1. If you are satisfied with our products and services, please leave your positive feedback of 5 stars . And 5 stars for the detailed rating of your order. We will of course give your positive feedback. 2. If you don't satisfied our porducts, pls contact us before you leave negative feedback. We guarantee we will 100% slove any problem for you. SHPING 1. Preparing Time: we need 3-7 working days to prepare your order, Ignoring how many days of proceing remains. 2. There is no limitied Order/Value in our store. We offer worldwide for any quantity and any value 3. APO/FPO/DPO Shping We apologize that P.O. Boxes and ary addrees (APO, FPO) cannot be delivered. shping REFOUND & EXCHANGE We have a QA team to test your ordered products are functioning correctly before they are packed and sent to you. But you do need to confirm your dre size carefully before buying (a size measurement will be show below each it). Atten: we can’t accept the exchange or canceling after your order has been shped. The following information is required when you reflect the problem: ----Order number ----Image/video of defective beads. If you have any question regarding return policy, please feel free to contact us! OUR GUARANTEE If you are not 100% satisfied with the quality of your purchase, you can return or exchange your it within 30 days from the delivered date. Request: 1. It received within 30 days from the delivered date. 2. It received unused, undamaged and in package. 3. Return shping fee was paid by buyer. About shping
Shping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.