Motorcycle Accessories Gear Indicator Gear Display Meter For Suzuki Bandit GSF650 GSF600 GSF1200 GSF1250 GSF 600 650 1200 1250

Condition:100%

Light Color:Red, green, blue, orange, white

1-6 Level Waterproof Gear Display

▶Fitment:

For Suzuki GSF600 Bandit 2000 - 2004

For Suzuki GSF650 Bandit 2005 - 2006

For Suzuki GSF1200 Bandit 2001 - 2006

For Suzuki XF650 Freezing 1997 - 2004

For Suzuki VL800 intruder Volusia 2001 - 2004

For Suzuki SV650 1999 - 2002

For Suzuki GSX1300R Hayabusa 1999 - 2007

For Suzuki GSX750F Katana 1998 - 2006

For Suzuki GSX600F Katana 1998 - 2006

For Suzuki GSX-R750 1996 - 2019

For Suzuki GSX-R600 1997 - 2019 K1 K2 K3
For Suzuki GSR600 ALL YEARS

For Suzuki GSR750 2011 - 2017

For Suzuki DL650 Vstrom 2012 - 2019

For Suzuki DL650XT Vstrom 1999 - 2002

For Suzuki TL1000 R/S 1998 - 2003

For Suzuki VL1500 intruder 2013 - 2017

For Suzuki VZR1800 2011 - 2019

For Suzuki intruder c1500 2013 - 2017

For Suzuki Boulevard c90 2013 - 2019

For Suzuki GSX250R 2018 - 2019

For Suzuki GSX1000F Katana 2019

For Suzuki GSX1400 2001 - 2009

For Suzuki GSXR1000 2001 - 2016

For Suzuki GSXS750 2015 - 2019

For Suzuki GSXS750Z 2018 - 2019

For Suzuki GSXS1000 /F/A/FA 2015 - 2019

For Suzuki GSXS1000Z 2018 - 2019

▶Locate the Speed Sensor connector:

The Speed Sensor is usually mounted on the front sprocket cover, and the 3-pole black speed sensor coupler (as shown in the figure) is situated 20-40 cm (8;-16;) away from sensor.

The connector is accessible raising the fuel tank, removing the seat or a side fairing(as shown in the figure).

▶Confirmation:

1. Separate the Speed Sensor connector (you might need to use a small flathead screwdriver to get the connector apart).

2. After separating the Speed Sensor connector, plug in both the male and female 3-pole GFYSHIP harness connectors. Make sure the connectors are fully seated.

3. Find the wire that comes from the Signal generator (Pickup coil / CKP sensor).

If in doubt, check the bike's Service Manual or ask your dealer.

4. Connect the Green wire to this wire, using the Red wire tap connector supplied.(The green wire is connected to the crankshaft sensor signal line)

▶Steps:

-You need to setup the module after . When ignition is turned on, the display counts backwards (6 to 1) indicating that the memory is clear.

-Raise the rear wheel off the ground using a stand, and start the engine in Neutral. (If you do not have a stand, you may setup the unit while riding. Find a , straight road with light traffic.)

-the screen displays L, indicating that learning is started.

- The screen displays L, select first gear, release the clutch, and keep the speed higher than the idle speed.

- The display will flash ''1'';. Continue to maintain the first gear, accelerate. When the device is learning a gear, the display flashes faster.

- When the display shows n, relax the handlebar accelerator.When the gear indicator changes from ''n'' to ''2'', the motorcycle immediately shifts into ''2'' gear, then continue to to refuel and accelerate slowly.

- When the display shows n again, relax the handlebar accelerator again.When the gear indicator changes from ''n'' to ''3'',the motorcycle immediately shifts into ''3'' gear, then continue to refuel and accelerate slowly.

Repeat this process until all gears are thought.

In the highest gear, when learning sixth gear, the display will flash 6, accelerate until o is displayed, and then 6 will stay on and stop flashing. Indicates that the configuration is complete.

The unit is programmed and should indicate the gears correctly.

Now, when ignition is turned on, the display counts forward (1 to 6) indicating that it is fully functional.


▶The steps to reset the product:

Turn on the key switch of the switch lock. When the gear indicator shows 3, turn off the key switch of the switch lock immediately, and then turn on the key switch of the switch lock immediately. According to the above operation, turn on and turn off the key switch of the switch lock six times in a row to see if the reset is complete(When ignition is turned on, the display counts backwards (6 to 1) Indicates that the memory has been cleared). Thank you

▶ video link:

1.https://www.youtube.com/watch?v=mn8vaoC5fsQ

2.https://www.youtube.com/watch?v=s9QevWTO4-Y

There could be some deviations due to manual measurement or slight color difference owing to photographing condition. Thank you for your understanding. If you do not understand what you can contact customer service at any time, I wish you a happy shopping.