M. 2 2230 Solid State Drive Heat Sink M2 NVMe For Steam Deck Hard Disk Copper Cooler Heat Sink Game Console SSD Heat Sink

SSD Copper Rust-proof Cooling Thermal Pad Antioxidant Copper Thermal Pad ed for Steam Deck Game Consoles

Feature:1. High Thermal Conductivity Copper Material:This solid state drive is made of pure copper material. This material is not only very ble, but it also has a high thermal conductivity. At the same time, it diipates heat more quickly by exchanging heat with air contact.2. Precise Dimension:This SSD copper uses precise dimension. It prevents installation deviation and short circuit. In addition, it fits into smaller mounting spaces, such as for Steam Deck M.2 2230 SSD.3. ly ed:This cooling thermal pad is ly ed. Its surface is smooth and burr-free. This prevents short circuits. It also resists rust as well as oxidation. It has a very long life span.4. Mini and Portable:This copper thermal pad is very mini and light. it is portable and convenient to use. whether you can carry it in your pocket. Whether you can carry it in your pocket, handbags or backpacks, it will not take up too much space and add preure to you. let your daily gaming and life more efficient.5. 0.5mm Thermal Conductive Silicon and 0.13mm Phase Change Heat Sink:This SSD copper cooler also comes with a 0.5mm Thermal Conductive Silicon, 0.13mm Photo Variable Heat Sink and a screw tool kit. This allows the to work better. Also, your installation will be more convenient and easier.

Specification:Origin: Mainland ChinaCompatible Brand/Model: STEAMModel Number: Solid State Drive Acceories Type: sMaterial: silicon wafer, copper, metal, etc.Size: 26x23mmWeight: 15gHard disk cooling installation tutorial:1. Turn the STEAM DECK off. Turn off the power to STEAM DECK and unplug all cables before replacing the hard drive.2. Remove the eight screws on the back of the STEAM DECK. (1) Use a screwdriver to remove the eight screws securing the back cover. four 9.5 MM screws and four 5.8 MM screws; (2) Keep the screws safe during the repment proce to prevent lo3. pry open the back cover.(1)Insert a tab along the edge of the right grip in the slit between the back cover and the front case; (2) Use the tab to pry up the back cover to loosen the clips4. Remove the protective plate. (1) use a screwdriver to unscrew the three screws holding the shield, one 3.4mm screw and two 3.7mm screws; (2) remove the screws and remove the shield5. Remove the SSD. (1) screw out the fixed SSD screws with a screwdriver; (2) remove the fixed screws and pull out the hard drive6. Install the (1) peel off the protective film; (2) peel off the thermal paste protective film to thermal paste, as shown in the picture on the surface of the hard disk particles; (3) align the to the hard disk and pre into the thermal slot7. Install the solid state drive. Insert the SSD with the installed back into the slot and tighten the screw. Put back the protective cover. After installing the hard drive, align the protective cover with the body screw holes and put it back on9. Install the protective cover. Put back the three fixing screws to fix the protective cover10. Install the eight screws on the back of the STEAM DECK. (1) Snap the back cover into the body; (2) Install the body screws to fix the back cover, installation is complete

Note:Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you!Please allow 1-2cm measuring deviation due to manual measurement.

1 x Copper Heat Sink2pcs x 0.5mm Thermally Conductive Silicone2pcs x 0.13mm Vario Heat Sink1 x Screwdriver2pcs x M2 Screws1 x Warp