LCR-TC1 LCR-T7 T10H nsistor Colorful Display TFT For Triode MOS NPN nsistor

If the quality problem of the product is found after receiving the express, please do not open the dispute at will. Please contact our after-s customer service to solve it in a timely manner. Thank you for your support and understanding!

Cautions for use

The shall not be d without discharge
The inductance of the nsformer cannot be d
Don't test online with electricity
Do not hook three hooks onto the circuit board for testing
Do not test live circuit boards
Otherwise, the will be t down. ing the is the buyer's reason.
When the voltage and internal battery are below 3V, please charge before use.
Please use 5V battery or USB port to charge.

LCR-T7 / LCR-TC1:color screen / Product chip: High-performance mcu, two functions are the same! T7 is slightly faster! The TC1 screen is slightly larger and they are all powered by lithium batteries. In addition to measuring resistance, capacitance, inductance, s, MOS nsistors, thyristors, it can also measure additional voltage regulators, infrared de limited to for Hitachi format

LCR-TC1

Feature:
S test with automatic calibration
Size: 70*90*26m/ 2.71x3.58x1.10 inch
Display:TFT Screen, Color Screen
Range: less than 4.5V
:nsistor Detect Area: 0.01-4.5V
Detect Area: 0.01-20V
Triac Range: IGT less than 6mA
Capacitance: 25pF-100mF
: 0.01-50MΩ
Inductance: 0.01mH-20H
Power Voltage: 3.7V
Product chip: High-performance mcu
Power: Built-in Rechargeable Lithium Battery
Measurement results using TFT graphic display 160x128

One-on operation
Auto power off timeout setting
Built-in high-capacity rechargeable lithium-ion battery
Lithium-ion battery voltage
Support Chinese and English
Warning: Built-in lithium-ion battery, it is strictly forbidden to immerse the in water or near heat source!
Warning: For your personal safety, please strictly observe the specifications and precautions for using lithium-ion batteries!
nsistor :
After the power-off state or test is completed, put the test component into the nsistor test area of the test socket, press the lohandle, press the multi-function key, the automatically measures, and the measurement result is displayed at the end of the test.
Warning: Always discharge the before connecting them to the ! The may be damaged before you turn it on!
Warning: We do not recommend using a to measure the battery! The battery voltage must be less than 4.5V, otherwise the may be damaged!
Component pment:
The test socket is divided into nsistor and test areas, as described in 1.1.
Note: Do not perform other operations during the calibration process to avoid affecting the calibration accuracy!
Packing List:
1 x multifunction TFT nsistor
1 x electronic component group
3 x test hook
Short the three test sockets, press the multi-function on shortly, and the will automatically calibrate.
No other operations are required after disconnecting the short wiring according to the prompt during the calibration process.

LCR-T7

nsistor :
After the power-off state or test is completed, put the test component into the nsistor test area of the test socket, press the lohandle,
press the multi-function key, the automatically measures, and the measurement result is displayed at the end of the test.
Warning: We do not recommend using a to measure the battery! The battery voltage must be less than 4.5V, otherwise the may be damaged!
Feature:
Automatic of 0.01-30V.
S test with automatic calibration.
Support Hitachi IR .
IR waveform display.
Infrared receiving instruction.
Measurement results using TFT graphic display.
One key operation.
Auto power off timeout settable.
Built-in high capacity rechargeable Li-ion battery.
Li-ion Battery voltage .
Used to detect NPN and nsistors, s, s, s, nsistors, N- and P- MOSFETs, IGBTs, JFETs, triacs and batteries
Specification:
Sweep range: 0.1MHz
Voltage: 3.7V
Display: 160 * 128 TFT
Battery: 1 * Li-ion battery, 3.7V, 300mAh
Package include:
1 *
1 * USB Cable
1 * Test Clip
1 * LED
1 * Capacitance
1 * Resistance

Product Description:

Easy to use, simply p the component in the testing area and press the START on. Start automatic measurement

Capable of testing s related to s, nsistors, s, s, and inductors

Capable of testing nsistors, MOS nsistors, thyristors, Darlington nsistors,

IGBT note: high-power thyristor, IGBT, may not be d accurately

And can automatically recognize the foot position and display it in graphics

Can test the en value of infrared e control only supports NEC format

The instrument comes with a lithium battery and does not require an external battery to be equipped with a USB charging cable

Attention:

Before testing the , it is necessary to discharge it first. Otherwise, it will directly damage the instrument

This instrument is an active instrument and should not be used to measure live circuit boards.

May cause damage to the circuit board