Lambda Air Fuel Ratio O2 Oxygen Sensor For Toyota Cruiser Corolla Yaris IQ Land Cruiser Prado Vitz Blade Altis IST 89467-52070

Warranty: Yes, 1 year warranty

Port Material: Copper andPlastic

Condition: In-stock, Brand-new, 100% test before send out

Application:

For Daihatsu Charade VIII 2011/05-2021/12 -- 1.33 16V 1329 ccm, 73 KW, 99 PS

For Lexus IS II 2005/10-2013/03 ALE2, GSE2, USE2 250 2499 ccm, 153 KW, 208 PS

For Lexus IS C 250 2009- (GSE2_) (GSE20) 4GR-FSE Convertible 2499cc,153kw,6Cyl

For Lexus GS 450h 2006-2011 (_S19_) (GRS191_, GWS191_) 2GR-FSE Saloon 3456cc,218kw,6Cyl

For Lexus GS 460 2007-2011 (_S19_) (UZS190_, URS190_) 1UR-FSE Saloon 4608cc,255kw,8Cyl

For Lexus GX 460 2010-2013 (URJ15_) 4WD 1UR-FE Closed Off-Road Vehicle 4608cc,218kw,8Cyl

For Lexus LS 460 2006- (_F4_) (USF40) 1UR-FSE Saloon 4608cc,280kw,8Cyl

For Lexus LS 600h 2007- (_F4_) (UVF45) 2UR-FSE Saloon 4969cc,290kw,8Cyl

For Toyota Auris 2010/01-2012/09 ADE15, NDE15, NRE15, ZRE15, ZZE15 1.33 Dual VVT-i 1329 ccm, 73 KW, 99 PS

For Toyota Auris 2009/05-2012/09 E15 1.33 Dual VVT-i 1329 ccm, 74 KW, 101 PS

For Toyota Corolla Stufenheck 2008/12-2014/07 E15 1.33 1329 ccm, 74 KW, 101 PS

For Toyota Un Cruiser 2009/01-2016/03 P1 1.33 1329 ccm, 73 KW, 99 PS

For Toyota Un Cruiser 2009/04-2016/03 P1 1.33 1329 ccm, 74 KW, 101 PS

For Toyota Yaris 2010/07-2011/05 KSP9, NCP9, NSP9, SCP9, ZSP9 1.33 VVT-i 1329 ccm, 73 KW, 99 PS

For Toyota Yaris 2008/11-2011/12 KSP9, NCP9, NSP9, SCP9, ZSP9 1.33 VVT-i 1329 ccm, 74 KW, 100 PS

For Toyota IQ 2009- (_J1_) 1.0 (KGJ10_) 1KR-FE Hatchback 998cc,50kw,4Cyl

For Toyota Land Cruiser Prado 2003-2009 (_J12_) 4.0 (GRJ125_, GRJ120_) 1GR-FE Closed Off-Road Vehicle 3956cc,183kw,6Cyl

For Toyota Prado 2002-2007 (_J1_) 4.7 (UZJ100) 2UZ-FE Closed Off-Road Vehicle 4664cc,175kw,8Cyl

For Toyota Vitz 2010/07-2011/05 (_P9_) 1.33 VVT-i (NSP90_) 1329cc

For Toyota Vitz 2008/11-2011/12 (_P9_) 1.33 VVT-i (NSP90_) 1329cc

For Toyota Blade 2009/05-2012/09 (_E15_) 1.33 Dual-VVTi (NRE150_) 1329cc

For Toyota Blade 2010/01-2012/09 (_E15_) 1.33 Dual-VVTi (NRE150_) 1329cc

For Toyota Altis 2008/12-2014/07 Saloon (_E14_, _E15_) 1.33 (NRE150) 1329cc

For Toyota Altis 2008/12-2014/07 Saloon (_E15_) 1.33 (NRE150) 1329cc

For Toyota IST 2009/04-2016/03 (_P1_) 1.33 (NSP110_) 1329cc

Oxygen Sensor's Location:Oxygen Sensor's Location:

How do I know the O2 sensor is good or not?

Check engine light on

A reduction in fuel economy.

Your catalytic converter fails unexpectedly

Exhaust emiions reach undesirable levels.

How to install the oxygen sensor?

Step 1 - Some are equped with a heat shield that must be removed before the sensor removal, this is performed by removing any mounting bolts.

Step 2 - By using a regular socket it minimizes potential damage to the sensor body and the threads, this technique helps avoid strping the old sensor upon removal.

Step 3 - Then, locate and disconnect the wiring connector, this step should be done before removing the sensor if the wiring is still attached.

Step 4 - Its ant that the wiring harne connectors are exactly the same, each sensor is unique to it's position and is located in the system by its connector configuration. (Note: some replacement have a universal electrical connector that must be configured to the wiring of the old sensor.)

Step 5 - Use a small wire brush to help clean the threaded port to ensure a proper seal of the new sensor. Gently install the new oxygen sensor by hand while keeping the wiring and connector free from bends.

Step 6 - Gently tighten the sensor while keeping wiring free from damage, these need to be fairly snug to avoid leakage.

Step 7 - Once the sensor is tightened, reinstall any heat shields or bracing that had to be removed.

Step 8 - After the heat shield has been reinstalled, mount the connector to it's holder and reattach the connector back onto the wiring harne. If the car has diagnostic trouble codes, they will need to be cleared.

We accept Credit Card, , WeChat Pay, PayPal, etc.

If you want to pay by PayPal, please contact us. Thanks!

All products will be tested strictly before shping. Please make sure your addre in is matched with your shping addre before you pay the order. And please make sure the mobile phone number and postcode is correct. In addition, Brazil and Chile customers please fill in the correct CPF number, so as to send your goods more quickly.

About shping
Shping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.