HoldPeak HP-770HC Dial True RMS Smart Autoranging Probe With NCV+HP-605A Clamp Adapter 600A AC DC Current

Item Name: HoldPeak HP-770HC Dial

About this item

• Non Contact Voltage TestNCV: When the of voltage is greater than 90VRMS, keep close to the conductor, the instrument r will light and buzz.

• Over load protection & continuity test: use the ptc protection circuit for resistance, temperature and frequency measurement. If measured resistance less than 100Ω, the will sound.

• Auto-ranging & auto-power off: dc & ac current 600A range with ac/dc current clamp adapter, resistance, , frequency, duty cycle, temperature, nsistor hfe.

• Low battery indication & blacklit lcd: 3 1/2 di lcd display for visibility in dimly lit areas. Feature a low battery indicator so you never accidentally run out of juice.

• Accurately measures AC/DC Voltage; AC/DC Current; Resistance, , Frequency and Temperature.

• nsistor hFE Test/ Non Contact AC Voltage NCV Test/ embly Test.

• Features Data Hold, LED Auto BaLight, Auto Power Off, Continuity , °C and ℉ Select; True RMS.

• With Function Switch Indication Lamp, Mechanical Blocking System, Max/Min and Relative Value Test.

Basic Function:
● Max LCD Display: 6000 Counts Di.

● DC Voltage Range: 60mV/600mV/6V/60V/600V/1000V

● AC Voltage Range: 60mV/600mV/6V/60V/600V/750V

● DC Current Range: 600uA/6000uA/60mA/600mA/6A/20A

● AC Current Range: 600uA/6000uA/60mA/600mA/6A/20A

● : 9.999nF ~99.99mF

● Frequency: 9.99Hz/99.99Hz/999.9Hz/9.999KHz/99.99KHz/999.9KHz/9.999MHz

● Resistance Range: 600/6K/60K/600K/6M/60M

● Temperature Range: -20°C ~ 1000°C/-4 ~1832℉

● Duty Cycle: 0.1% ~ 99.9%

● nsistor hFE Test Range: 0 ~1000; Ib=10µA, Vce=1.8V Approx.

● Weight: 1.8 pounds

● Dimension: 7.7 x 3.5 x 1.6 inches

Iterm Name: HoldPeak HP-605A AC/DC Clamp Adapter

About this item

• 【AC/DC 600A Clamp-on Probe】Capable of measuring AC/DC up to 600 amps, BT-605A clamp adapter is built for higher current measurement.

• 【Great Companion to DMMs】1mV per ampere output & standard 3/4 inch banana plugs es it compatible with most multis that features with 1mV sensitivity.

• 【Accurate Ampere Measurement】+/- 3.0%+10 accuracy for signal output conversion. The arrow on the Jaw indicates the DC current direction of positive current flow from positive to negative

• 【Easy to Use】Maximum Jaw Caliber Size up to 1.77 inches 45mm, allows you to e accurate AC or DC amperage measurement up to 600 amps without breaking the circuit.

• 【Tips】Putting an amp-clamp on a power cord wouldn’t get a reading, you’ll need to put an amp clamp around the live wire only, or use an “AC line splitter”.

Basic Function:

● DC Current: 600 A

● AC Current: 600 A
● Jaw Caliber: 1.77inch

● Output Conversion: 1mV/1A
● Conversion Accuracy: +/- 3.0% + 5 dis
● Output Impedance: 10K

● Dimension: 7.05*3.54*1.42 inch

Tips for HP-605A:

▶Perfectly work with HOLDPEAK s, such as: HP-770M, HP-770N, HP-770K, HP-90EPD, HP-90EPC, HP-6688G, HP-6688H, etc.

▶When perform DC current measurement, always press “REL” key on to zeroes it out.

▶When perform AC current measurement, always use the clamp go round the live wire only, or use "AC line splitter"

▶Connect the blabanana plug of the BT-605A AC/DC Current Clamp Adapter to "COM" port and the red banana plug to the "µA mA" port.

▶Press “SELECT” on on the and press AC/DC on on the Clamp Adapter to choose “DC” or “AC” measurement .

▶The arrow on the right side of the Jaw indicates the DC current direction of positive current flow from positive to negative .