FOCAN 36V 48V 450W 500W Electric Bike Brushless Motor Controller with LCD Display G51 Electric Bicycle Scooter E~bike Parts

Note:

Not Universal Model .Only Used FOCAN Controller with FOCAN-LCD Display.

Item Type: Electric Display Screen

Model : LCD Display +DC Brushle Motor Controller

Product Material: ABS

Voltage: DC 24V 36V 48V 52V 60V（Adjust Voltage By P03 set )

Suitable For Mounting Handlebars: 22.2mm Diameter Handlebars

Plug Type : SM 5pin Connector (LCD cable )+ SM 2pin connector (Light cable)

DC Brushle motor controller :

Condition: 100%

Material: Aluminum+Plastic

Controller Rated Voltage:36/48V

Limited Current :23±2A

Speed set:1.1-4.2V

Power :450W

Suit for :350W-500W DC Brushle Motor

Applicable model: electric bicycle, electric scooter, electric vehicle, toy scooter etc

Note: Due to product upgrade, the product you purchased may beslightly differentfrom the descrtions in this user manual, and this won’taffect normalusage.

Package List:

1 x LCD Display

1 x Controller

Please note that the controller model will be sent ly, and e sure you will not mind before ordering.

P00: Restore Factory SettingsSet this value to 10 and switch to setting, the display it will show all contents and restore factory settings.

P01: Backlight Brightne(1: darkest; 3: brightest)

P02: Mileage Unit(0: KM; 1: MILE)

P03: Voltage Cla24V/36V / 48V

P04: SleepInterval

(0: never, other valuemeansdisplaeep interval) Unit: minute

P05: Power Aist Gear

0/3 Gear Mode: Gear 1: 2V  Gear 2: 3V  Gear 3: 4V

1/5 Gear Mode: Gear 1: 2V  Gear 2: 2.5V  Gear 3: 4VGear 4: 3.5V  Gear 5: 4V

P06: Wheel DiameterUnit: inch    Precision: 0.1

P07: Steel Number (for Speed Test)    Range: 1-100

P08: Speed Limit

Range: 0-50km/h, 50 indicates no speed limit.

1. Non-communications status (panel-controlled)

When the current speed exceeds the speed limit, the PWM output will be shut down; when the current speed falls to lower than the speed limit, the PWM output will be activated and the driving speed will be set as the current speed ±1km/h (only applies to aist power speed, not applicable to the handlebar speed).

2. Communications status (controller-controlled)

The driving speed will be kept constant as the limited value.

Error Value: ±1km/h (applicable to both the aist power/handlebar speed)

Note: The above-mentioned values are measured by metric unit (kilometers). When the measuring unit is switched to imperial unit (mile), the speed value displayed on the panel will be automatically switched to corresponding imperial unit, however the speed limit value in the imperial unit interface won’t change accordingly.

P09: Direct Start / Kick-to-Start Setting

0: Direct Start

1: Kick-to-Start

P10: Drive Mode Setting

0: Power Aist – The specific gear of the aist drive decides the aist power value. In this status the handlebar does not work.

1: Electric Drive – The vehicle is driven by the handlebar. In this status the power gear does not work.

2: Power Aist + Electric Drive – Electric drive does not work in zero-start status.

P12:  Power Aist IntensityRange: 0-5

P13:  Power Steel Number5 / 8 / 12pcs

P14:  Current Limit Value:  12A by default; Range: 1-20A

P15:  Unspecified

P16:  ODO Zero-Out