DIY Voice Sound Module 30s 60s 4min Light Control Record Greeting Card 10s Infrared Trigger Record 36 Doorbell Music Loudspeaker

Condition : NewType : Voltage RegulatorBrand Name : IS : Mainland ChinaISD1820 10s Infrared Trigger Record
1.Description:It is a ISD1820 recording module.It can directly drive 8 ohm 0.5W small speakers,which can be played by single chip,infrared or other external trigger.2.Feature:1>.Convenient 10-second voice recording and playback2>.High-quality,natural speech restoration3>.It can be used as a megaphone module4>.With loop/jog/single-pass playback function5>.It can be controlled by a single chip microcomputer6>.This module can be directly driven3.Description:1>.Product Name:ISD1820 Recording Module2>.Power Supply:3V~35V,It can be connected to the pin to power on or directly connected to the power supply terminal.3>.Recording and Playback Control Mode:on control,microcontroller or infrared trigger,control line IO has been led out4>.Work Temperature:-25℃~85℃5>.Work Humidity:5%~95%RH6>.Size:57.5*44*18mm4.on Control Recording and Playback Operation Method:1>.REC on:Recording on, press to record,release the on to stop recording2>.RLAYE on:Trigger mode playback,click to play the current entire segment of voice3>.PLAYL on:Play in jog mode,press and hold to play,release to stop playing4>.RPL Jumper:Loop playback mode control,loop playback5>.FT Jumper:Pass-through control,can make microphone voice pass through to the speaker for playback6>.External Trigger:External trigger signal playback of MCU,onboard infrared trigger or external trigger playback5.Package:1>.1pcs ISD1820 Recording Module2>.1pcs Horn
36 Doorbell Music Module Type
1.Description:
It is a FLM036A music module.It has a wide range of applications and can be used for wired doorbells,wireless doorbells,smart door locks,musical toys,timekeeping alarms,and so on.
2.Feature:
1).It can play 36 doorbell music.
2).It has ons for selection,volume,and playback,which are convenient for operation according to the situation.
3).It uses battery power supply,only need to prepare 3 AAA batteries,you can start working.
4).The module has a speaker,no need to prepare an additional speaker.
3.Parameter:
1).Product Name:FLM036A Music Module
2).Doorbell Music:36 songs
3).Supply Voltage:DC 4.5V
4).Work Temperature:-25℃~85℃
5).Work Humidity:5%~95%RH
6).Circuit Board Size:52*23*10mm
7).Speaker Size:40*40*5mm
8).on Size:12*12*5mm
9).Battery Case Size:53*37*14mm
4.Package:
1).1pcs FLM036A Music Module
2).1pcs Battery Case
3).1pcs Trumpet60s Light Control Record
1.Description:
It is a light control recording module.After the recording is finished,the module sensor will play the recorded sound once when it senses the light,and the playback can be stopped when the light is blocked.
2.Feature:
1).Its recording time is ,up to 60 seconds.
2).It comes with a speaker and battery,so no additional preparation is required.
3).Its operation is simple,anyone can operate it.
3.Parameter:
1).Product Name:Light Control Recording Module
2).Recording Time:60 seconds
3).Play Mode:play once in the light
4).Power:0.25W
5).Work Temperature:-25℃~85℃
6).Work Humidity:5%~95%RH
7).Module Size:49*28*9mm
8).Speaker Size:40*40*5mm
9).on Size:12*12*5mm
4.Instructions:
1).Pull out the transparent insulating sheet under the battery before it can work normally.
2).Press and hold the recording on (the on with the red wire),and after hearing the "di" sound,speak to the microphone about 5 cm away to start recording.After speaking,release the recording on and hear the "di" sound indicating that the recording is complete ,The photosensitive sensor will play the recorded sound once when it is exposed to light,and stop playing when the light is blocked.
5.Package:
1).1pcs Light Control Recording Module
2).1pcs Speaker
3).1pcs on
4).1pcs Light Sensor30s Light Control Record
1.Description:
It is a light control recording module.After the recording is finished,the module sensor will play the recorded sound once when it senses the light,and the playback can be stopped when the light is blocked.
2.Feature:
1).Its recording time is ,up to 30 seconds.
2).It comes with a speaker and battery,so no additional preparation is required.
3).Its operation is simple,anyone can operate it.
3.Parameter:
1).Product Name:Light Control Recording Module
2).Recording Time:30 seconds
3).Play Mode:play once in the light
4).Power:0.25W
5).Work Temperature:-25℃~85℃
6).Work Humidity:5%~95%RH
7).Module Size:49*28*9mm
8).Speaker Size:40*40*5mm
9).on Size:12*12*5mm
4.Instructions:
1).Pull out the transparent insulating sheet under the battery before it can work normally.
2).Press and hold the recording on (the on with the red wire),and after hearing the "di" sound,speak to the microphone about 5 cm away to start recording.After speaking,release the recording on and hear the "di" sound indicating that the recording is complete ,The photosensitive sensor will play the recorded sound once when it is exposed to light,and stop playing when the light is blocked.
5.Package:
1).1pcs Light Control Recording Module
2).1pcs Speaker
3).1pcs on
4).1pcs Light Sensor4min Light Control Record
1.Description:
It is a light control recording module.After the recording is finished,the module sensor will play the recorded sound once when it senses the light,and the playback can be stopped when the light is blocked.
2.Feature:
1).Its recording time is ,up to 4 minute.
2).It comes with a speaker and battery,so no additional preparation is required.
3).Its operation is simple,anyone can operate it.
3.Parameter:
1).Product Name:Light Control Recording Module
2).Recording Time:4 minute
3).Play Mode:play once in the light
4).Power:0.25W
5).Work Temperature:-25℃~85℃
6).Work Humidity:5%~95%RH
7).Module Size:49*28*9mm
8).Speaker Size:40*40*5mm
9).on Size:12*12*5mm
4.Instructions:
1).Pull out the transparent insulating sheet under the battery before it can work normally.
2).Press and hold the recording on (the on with the red wire),and after hearing the "di" sound,speak to the microphone about 5 cm away to start recording.After speaking,release the recording on and hear the "di" sound indicating that the recording is complete ,The photosensitive sensor will play the recorded sound once when it is exposed to light,and stop playing when the light is blocked.
5.Package:
1).1pcs Light Control Recording Module
2).1pcs Speaker
3).1pcs on
4).1pcs Light Sensor4min Repeat Recording
1.Description:
It is a recording module.It can perform repeated recording,and each recording will overwrite the previous recording.
2.Feature:
1).It can record for 4 minutes,which can meet your recording time requirements.
2).It has an 8ohm speaker,no need to prepare an additional speaker.
3).It has a recording on (red line) and a playback on (black line) for easy operation during recording.
4).It supports loop playback mode,which can be played all the time.
3.Parameter:
1).Product Name:Recording Module
2).Recording Time:4 minutes
3).Working Voltage:DC 3.0V-4.5V
4).Play Mode:loop play
5).Work Temperature:-25℃~85℃
6).Work Humidity:5%~95%RH
7).Module Size:32*22*10mm
8).Speaker Size:40*40*3mm
9).on Size:12*12*5mm
10).Battery Case Size:53*37*14mm
4.Recording and Playback Operations:
1).Press the record on,release the record on when you hear a "beep" sound,and then face the microphone at a distance of 5-10 cm
After speaking,start recording,press the recording on again,and release the recording on when you hear a "di" sound,indicating that the recording is complete.
2).Then press the play on again to play the currently recorded sound.During the playback process,press the play on again to stop playing the sound.
5.Package:
1).1pcs Recording Module
2).1pcs Speaker
3).2pcs on
4).1pcs Battery Case