DIY Multifunction Clock Car Temperature Battery Voltage Monitor Voltmeter DC 12V

DIY Multifunction High-precision clock inside and outside Car temperature Battery voltage Monitor Panel Meter DC 12v

Descrtion: Multi-functional electronic clock module, set time, inside and outside temperature, voltage as one. You can display a single item, or you can cycle through the it alternately and customize the item to be displayed. Time using Epson's RX8025T , this is a temperature compensated clock , time accurate. Standard 0.3 m +1.5 m module with two waterproof probes, temperature range -35 ~ 120 degrees. With brightne adjustment, 3 brightne adjustable. And automatic brightne function, can be dark at night, brighten during the day.

Specifications: 1, working voltage: DC 5.0 ~ 28V 2, frame size: 22 * 58 mm 3, Installation hole size: 19.5 * 56 mm 4, Voltage display range: 5.0 ~ 28V 5, temperature display range: -35 ~ 120 ℃ （Two temperature ，0.3 meters +1.5 meters） 6, power lead length: 28CM

How to use: UP the key: Under normal display, preing this key will switch between the six display states of 【Time】 → 【Date】 → 【Temperature 1】 → 【Temperature 2】 → 【Voltage】 → 【Alternating Cycle Display】. (Note: The display it and switching interval time in alternate cycle display mode can be customized by "dd" and "dF" parameters respectively. See the following table Under the key: Under normal display status, pre this key to enter the setting of time \ date \ year \ parameter. Pre the key, "points" began to flash, pre the on to adjust the value. After adjusting, pre the key again, "hour" starts flashing, pre the key to adjust the value. And then pre the key to enter the date adjustment [Note that the middle of the colon is not lit], "day" began to flash, pre the key after the tune "month" began to flash, tune and then pre the key "year" start Flashes, pre the key to adjust the parameters into the extended set, see the following "code significance and role of the table" The significance of the code, please refer to the following 1.0.0u Voltage measurement error correction, a positive number increases, a negative number decreases. For example, the actual supply voltage is 12.0V, but the table shows 11.9V, it is adjusted to 0.1u. 2.Ac Temperature ① error calibration parameters. Positive number increases, negative number decreases, the unit is degree, the adjustment range is -5 ~ 5. For example, if you think the displayed temperature is 1 degree higher than the actual temperature, then set Ac: -1, so the electronic clock is automatically reduced by 1 degree and displayed. (Note: If you do not have a standard thermometer for reference, it is recommended to keep this as Ac: 0) Temperature ② error calibration parameters. Positive number increases, negative number decreases, the unit is degree, the adjustment range is -5 ~ 5. For example, if you think the displayed temperature is 1 degree higher than the actual temperature, set it to AC: -1, so that the electronic clock is automatically suracted by 1 degree and displayed again. (Note: If you do not have a standard thermometer for reference, it is recommended to keep this as AC: 0) 3.dd Custom cycle shows the display item [dd: 0] time + temperature 1 + temperature 2+ voltage [Dd: 1] time + temperature 1 + temperature 2 [Dd: 2] time + temperature 1 + voltage [Dd: 3] time + voltage 4.Df Switch the time interval in custom cycle display, the unit is second, the adjustment range is 1 ~ 9. For example, dF: 3, the switching interval is about 3 seconds to switch the display item once.(Please do not set to "0") 5.LL Display brightne level, the adjustment range is 1 ~ 3, LL: 1 is the darkest, LL: 3 is the brightest. 6.AL Auto brightne control switch, AL: 0 to turn off the automatic brightne control, AL: 1 to turn on the automatic brightne control. When set to AL: 1, the electronic clock will change the brightne to level 1 after 19:00 everyday and change this level to level 3 every day after 07:00 am. note: After adjusting the AL option, pre "Down" again to return to the normal display state, all parameters and time settings can be saved.

Package include: 1pc DIY Multifunction Clock Temperature Voltage Monitor Panel Meter

About shping
Shping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.