Digital power supply case S800 S12D and Switch Power Supply for RD6012 RD6018 only metal housing not contain power supply

800W PSU can let RD6018 output 18A, or let RD6018 output 60V, but it cannot let RD6018 full output 60V/18A because it is lower than the max output power of RD6018(1080W)

1000W PSU is 68V 17A output at 220V AC input, it can let RD6018 full output, but it is 68V 14.7A (about 1000W) at 110V AC input, so it cannot let RD6018 full output, please set the power limit to 950W in RD6018 setting.

NOTE for Switching power supply: When get the PSU, please use multimeter to check if the real output voltage is stable and fits the rated voltage, to see if it is damaged on the way, if the output is abnormal, please contact us, do not connect it to RD power supply to avoid more lo

Technical Support If you have any questions about our products, welcome to contact us in these ways,for now we support Tencent QQ group, WeChat group and WhatsApp, here is the contact information. QQ Group:550112838 WeChat:15868147353 WhatsApp:+8615868147353

Note before buying:

1, those 2 choice S800 case and S12D case are only case, not containing any power supply. some picture show installation finished by RD6012 , switch power and case .

2, there are 2 choice, S800 case and S12D case . For S800 case, you can put AC switch power and RD6012 into this case. for S12D, you can only put RD6012.

RD6012/RD6018 and S800 case aemble instruction : https://drive.google.com/drive/folders/1LNymuq8olL32XDJXZFeQow7xtbuP6bMI?usp=sharing

RD6012 /RD6018 and S12D case aemble instruction : https://drive.google.com/drive/folders/1T66hTdQfkDyEG0yMzu-64BNY5Za8CmSn?usp=sharing

Installation video : https://youtu.be/RkIH9xOx_5M

there may be scratches on the surface but it doesn't affect the product performance, please do not be over picky, and if you do mind this, please do not buy this product

3, for S800 case, it is just case, not conntaining any power supply, but it is suitable for RD6012/RD6012W and AC 800w switch power supply, you can buy them seperately to aemble.

5. install the device in the right way

Friendly reminder: ·there may be high-frequency noise when the 800W 65V switch power supply is powered on and there is no load, which can be improved by adding a load resistor as shown in the figure! But for some people, they can still hear the noise, if you mind the noise, please do not buy this power supply, 800W 68V PSU does not need this ·You can only connect the cables with a foundation in electronic and electrical engineering and it must be reliably grounded! ·Due to expre delivery, some power supply warranty labels may be damaged, which does not affect product warranty! ·Due to the different power supply production batches, the internal material details may be different, hereby explain!

5, for S800 case, durning the shipping, maybe the case side wiil be a little deformation (just like picture ), you can use your hand to ajust, that's ok, if you  do mind this , please stop buying.

6.when intall our 800W PSU into our case, please follow our instruction to aemble, do not remove the shell of the PSU to use. After the shell of the switching power supply is removed, the structural change of the heat diipation system will lead to insufficient heat diipation,and some components will be overheated and damaged, in this case we don't offer after sell service

S800 Case Instruction:

Digital power supply case (S800) aembly instruction

This case is suitable for RD6012

Date:2020.5.11

Dear users, thank you for purchasing the digital power supply acceory-metal case produced by Hangzhou Ruideng Technology Co., Ltd. In order to let you know more about the full function of this product, get a better experience and avoid misuse. Please read this instruction carefully before aembly. Keep it for future reference.

ATTENTION: Since the aembly proce involves voltage that exceeds the human body's safety, non-profeionals should not operate, you must do insulation and protective measures during the aembly proce, and check the wiring several times for safety, please place the product at a place that children and old people cannot get.

Please use the switch power supply we recommend, and if you use other power source, check if the positions of fixing holes are suitable or not.

2.Product Dimension

3.Acceory List

NAME

SPECIFICATION

QUANTITY

PICTURE

Upper Board

S 800 upper board

1

Lower Board

S 800 lower board

1

Connection

Cables

Brown 32cm：1

Brown 10 cm：1 Yellow Green 32cm：1

Blue 32cm：1

Red 17cm： 2

Black 17cm： 2

Temperature sensor extension board :1

9

Rocker switch

KCD3

1

AC power socket

AC-04

1

Non-slmats

Φ13*4

4

Screws for fixing mats, extension board andswitch power supply

M3*4 round head

11

Screws for fixing case and AC power socket

M3*6 flat head(white)

10

4.Acceory Picture

A: Lower Board

B: Upper Board

C: Screws for fixing mats, extension board and switch power supply

D: Screws for fixing case

and AC power socket

E: Non-slmats

F: Rocker switch

G: AC power socket

H: Connection Cables

5.AemblyProcedure

5.1 Aembly Preparation

● RD60 XX digital power supply*1, S 800 case*1,800W switch power supply*1

● Tools, acceory(DC power supply, 3 pin plug cable, multimeter, screw driver, test pencil...)

● Proper aembly environment

It is recommended using a 800W switch power supply as shown below.

5.2 Aembly step

Note: The case material is a bit soft and may be slightly deformed during transportation. If there is a gap during the aembly, please straighten it before aemble it.

①Check the acceories: check if the acceories ofS800are same as acceorieslist or acceory picture.

②Check RD60XX:Adjust input power supply to 12v/1A to power on RD6012, and set 5V/1A output on RD60XX, turn on the output to see if the output is normal.

③Back board aembly: install the rocker switchandAC power socketon the lower board.

④Connect cables to switch power supply: (dangerous,non-profeionals should not operate)

Uselongbrown cable to connect therockerswitch and the live wire (L) of the switch power supply; then useshortbrown cable to connect therockerswitch and the live wire (L) of the AC power socket; Use the blue cable to connect the neutral wire (N) ofAC power socket and the neutral wire (N) of switch power supply; Use a yellow-green two-colorcableto connect the ground wire (E) ofAC power socket and the ground wire (〨) of switch power supply.Use two red cables to connect the IN+ of the green terminal and the positive electrodes (+V), and use two black cables to connect the (IN-) of the terminals and negative electrodes (COM). Install the temperature sensor extension board to the back panel.

If you want to use S800 for RD6024, you need to solder the connector to the cables first, then you connect the RD6024

⑤Aemble the switch power supply：Installthe switch power supply on the lower board

⑥switch power supply test:

Check the wring again and power on the switch power supply, and use test pencil to check the power and insulation status. Then use multimeter to check if the output is normal, then use screw driver to adjust the output of the switch power supply to about 68V.

⑦RD60XX aembly：If you have CR1220 battery, pleaseinstall the battery with the positive side facing up, if you have WiFi module, please install it like what shows in the picture. InstallRD60XX to the front side in the correct way, otherwise it cannot be installed properly, we make flame tight to prevent the RD60XX from shaking, if the case is slightly deformed, you can gently bend the case to make itstraight.

⑧Connect the rest cables:insert the external temperature sensor cable, insert the green terminal and sort out the cables.

⑨Install the screws of the case

⑩ Install the foot pads.

⑪If you need to use external temperature detect, you can insert the external temperature sensor cable to be back end of the case, and do final test.

S12D Case Instruction: Digital power supply case (S12D) aembly instruction

This case is suitable for RD6006/RD6006-W/RD6012/RD6012-W

Date: 2020.5.21

Dear users, thank you for purchasing the digital power supply acceory-metal case produced by Hangzhou Ruideng Technology Co., Ltd. In order to let you know more about the full function of this product, get a better experience and avoid misuse. Please read this instruction carefully before aembly. Keep it for future reference.

1.Notes

● Read this instruction carefully before aembly, if you still have question, please contact us.

● This case is made of cold-rolled steel plate and the surface is sprayed. When aembling and using, prevent it from scratching by sharp objects, and avoid direct sunlight and humid environment.

● Avoid short circuit when aembling, connect the electrodes correctly.

● NEVER connect the cables with the power ON.

● Try to avoid vibration and fall.

2.Product Dimension

3.Acceory List

NAME

SPECIFICATION

QUANTITY

PICTURE

Upper Board

S12D

1

Lower Board

S12D

1

Cable

RED：2

BLACK：1

3

Female Banana Socket

M4*36

2

Rocker switch

KCD3

1

Non-slmat

Φ13*4

4

Mat fixing screw

M3*5*7

4

case fixing screw

M3*6

flat  head  white

8

4.AcceoryPicture

A: Upper Board

B:Lower Board

C: Non-slMat

D: Screws for Non-slMat

E: Case Fixing Screw

F: Cable

G: Rocker Switch

H: Female Banana Socket

5.AemblyProcedure 5.1 Aembly Preparation

● RD series digital power supply*1, S12D case*1

● Tools, acceory (DC power supply, screw driver)

● Proper aembly environment

Note: The case material is a bit soft and may be slightly deformed during transportation. If there is a gap during the aembly, please straighten it before aemble it.

5.2 AemblyStep

1. Check the acceories:

Check if the acceories of S12D are same as acceory list or acceory picture.

2. Install the female banana sockets and switch:

Please put the female banana sockets and rocker switch on the corresponding position of back board, the red female banana socket is positive electrode and the black female banana socket is negative electrode. Screw the fixing screws.

1. Connect cable

Use cables to connect switch and female banana sockets, and tighten with nuts, the wiring is completed, you can see the final connection below:

1. Connect the terminals, you can connect the U-shaped plug directly to the green terminal of RD6012/RD6012-W, and you need to cut off one side of U-shaped plug and connect them to the green terminal of RD6006/RD6006-W.

5. Install the RD power supply: install the power supply on the front, and insert the green terminal to the power supply, and then connect the external temperature sensor.

6.  Use 12V/1A DC power source to power on the RD series power supply, check if the connection succeeds (check the wiring before power on)

7.  Install the upper board: install the upper board on lower board, and use screws to fix it.

8.  There are four Non-slip mats, please use screws to fix them.

About shipping
Shipping and Packaging All itwill be double checked and well packed before sending.Itwill be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resolve the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.