DC12V 24V 3200rpm Brushless motor built-in driver

be careful:

We prepared the line separately,

So the color of the line is not used to define the positive and negative poles,

The yellow wire of this motor is connected to the positive pole,

The black wire is connected to the negative pole,

The red line is the PWM signal,

If the red line is connected to the yellow line,

The motor runs at maximum speed.

Brushle DC motor,

The positive and negative poles shall not be connected reversely,

The yellow wire is connected to the positive pole,

The black wire is connected to the negative pole,

The red line is the PWM signal,

If it is connected incorrectly, the drive board will be burned.

New brushle motor,

The shell cannot be separated,

The lead of the motor is three wires,

Easy to use,

Using only one set of DC24V,

The motor can operate normally,

It also supports speed regulation with PWM signal input.

Thick wire diameter of motor,

high-power,

The no-load current at the maximum speed of DC24V is 0.7 a.

Note:

The yellow wire is connected to the positive pole,

The black wire is connected to the negative pole,

If the connection is reversed, the drive plate will be burned out.

Please carefully define the line before energizing.

This motor has two wiring methods:

1 .

The yellow and red wires are connected in parallel to the positive pole,

The black wire is connected to the negative pole,

The negative pole of PWM signal is connected to the black line,

The motor runs at the highest speed,

At this time, if the voltage is adjusted,

It can also adjust the speed,

The measured speed is as follows:

DC12V ，     0.31 A，        1000 RPM；

DC18V ，     0.57 A ，        2000 RPM；

DC24V ，     0.70 A  ，       3200 RPM。

2 .

The yellow wire is connected to the positive pole,

The black wire is connected to the negative pole,

Red line input PWM signal,

(the pulse frequency is about 1000 Hz),

In this way, adjusting the duty cycle is to adjust the speed,

The no-load speed and no-load current of the motor under different duty cycle are measured below.

Weight: 568g

Motor steering: CW

The current and speed measured at different duty cycles are as follows:

10%,      0.07 A,        174 RPM;

20% ,     0.10 A ,       392 RPM;

30% ,     0.16 A,        588 RPM;

40% ,     0.25 A,        855 RPM;

50%,      0.37 A  ,      1170 RPM;

60%,      0.46 A ,       1517 RPM;

70%,      0.54 A ,       1880 RPM;

80% ,     0.68 A  ,      2400 RPM;

90% ,     0.68 A ,       2650 RPM;

99% ,     0.68 A ,       3200 RPM.

Remind me again of ant things:

These motors are connected to the positive pole with yellow wire,

The black wire is connected to the negative pole,

The red line is connected to PWM,

If the positive and negative electrodes are connected reversely, the driving plate will be burned.

About shipping
Shipping and Packaging All itwill be double checked and well packed before sending.Itwill be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.