DC 5-30V 5V 12V 24V 433Mhz RF Wireless e Control Switch Relay 1CH Receiver Module For LED Door Electroic LoDIY

DC 5-30V 433 Mhz RF Wireless e Control Switch relay 433mhz 1CH Receiver Module For Learning code nsmitter e DIY

Specifications Of The Receiver:
Model Number : RYO-XPX-5P
RF Working Mode: rheterodyne Reception
Modulation Mode: ASK
Working Mode: Momentary, Tole, Latching and Time Delay Mode.
Input Voltage: DC 5 ~ 30V
RF Frequency: 433MHz
Quiescent Current: 5mA
Receiving Sensitivity: >97dbm
Theoretical e control distance:>80-100mThe actual distance has losses depending on the application method
Wired Connection Way: Fixed Wiring ar.
De Mode:MCU De.
Working Mode:Momentary, Tole, Interlocked Mode Latching Time delay 5s ,10s ,15s

Specifications Of The nsmitter:

Model Number : J027
Operating Frequency: 433MHz
Power by 3V Coin Cell on Battery Battery included
Material: PVC
on: 2 ons
Size: 59mm x 28mm x 8mm
Operating Voltage: 3V
Operating Current: 12mA
nsmitting Power: 10mw
Modulation Mode: ASK AM
En Type: Learning
nsfers Distance: 20-50 m

Operation Introduction:

About Working Mode:

Momentary: Press the e on, the relay connects, release the e on, the relay disconnects.

Tole: Press once the e on, the relay connects, press the e on twice, the relay disconnects.

Latching: Press the e on A, the relay connects, press the e on B, the relay disconnect.

Time Delay Mode: Press the e control on, the relay connects; Start timing when release the e on, the relay disconnect automatically after 5s or 10s or 15s.


Clearing the Code:
Press the Learning on on the receivers for 8 times, the codes will be cleaned.
After cleaning the code, all the e control cannot work any more.

Learning the Code:Momentary
Press the learning key on the receiver once time, it comes into momentary setting mode.
Wait for a moment, the LED will be off , it comes into learning state.
Push the e on, LED indicator on the receiver board will f then come off.
After 3 seconds, the LED indicator will be on again, learning successfully.

Learning the Code: Tole
Press the learning key on the receiver twice time, it comes into tole setting mode.
Wait for a moment, the LED will be off , it comes into learning state.
Press the e on, LED indicator on the receiver board will f then come off.
After 3 seconds, the LED indicator will be on again, learning successfully.

Learning the Code: Latching
Note: When you choose for latching mode, in order to learn more e control, you need to learn two different on, the first time learning is for ON, the second time learning for OFF.
For example: on A = ON, on B = OFF
Press the learning key on the receiver tre time, it comes into latching mode .
Wait for a moment, the LED indicator on the receiver board will f then come off.
Press the e on A. LED f for 5 times.
Press the e on B. LED f for 5 times
After 3 seconds, the LED indicator will be on again, learning successfully.
A = ON, B = OFF .

Learning the Code :Time Delay Mode
Press the learning key on the receiver four times, the time delay for 5 seconds.
Press the learning key on the receiver five times, the time delay for 10 seconds.
Press the learning key on the receiver six times, the time delay for 15 seconds. The LED indicator will be off . Press the e on, LED fes and off.
After 3 seconds, the LED indicator will be on again, means learning successfully.

Power-on function learning method:
Continuously press the control panel code on 8 times, the LED indicator awith the blinking 1 time, and so the LED indicator light up and press the e control on that needs to code, the control panel LED indicator fes 3 times, code successfully. Note 1: This function is the power on the relay automatically absorbed also known as the incoming call to turn on the light function Note 2: Learned "power on" function such as changing the other operating modes must be implemented to clear the code