D2~1 Intelligent cking Line Car Photosensitive DIY Kit Smart Car Kits Patrol Automobile Parts DIY Electronic Toy

PLEASE READ BEFORE PAYMENT!!!!

The products which are suitable for electronic enthusiasts to study and repair circuits. We only guarantee that the products are in good condition before delivery, and cannot guarantee 100% succe ar installation. The installation of the circuit requires the buyer to have experience in the circuit, please read the product descrtion carefully before payment.

We do not accept disputes cad by the fai to work properly due to installation errors. In this case, we will blacklist and complain to the buyer.

since air nsportation does not allow products to contain batteries, if there are batteries, the package will be destroyed. All products will not contain any batteries!

Descrtion:L93 comparing two photosensitive resistance, when the imbace (eg side preure runway black) immediately control side of the motor stops rotating, the other side of the motor rotation acceleration, so that the car modification direction, return to the right direction, the whole proce is a closed loop therefore rapid and sensitive control.With the aim of simplifying the complex prince, we first have a by dial circuit to the intelligent cking car, in the aembly proce, we could not only familiar with the mechanical prince gradually can learn to: photocell, a voltage comparator, a motor drive circuit, and other related electronic knowledge.photosensitive resistance deviceThis is light-sensitive resistance, it can detect the external light intensity, the stronger the outside light photosensitive resistance resistance is small, the outside light weaker resistance is greater when the red LED light projected on a and black runway beca reflection rate is different, the resistance value of the light-sensitive resistance will occur obvious difference for subsequent circuit control.L93 comparator integrated circuitL93 is a dual voltage comparator integrated circuit, which consists of two independent precision voltage comparator. its role compare the two input voltage, based on the level of two input voltage change the level of output voltage. The output has two states: close to open or close to the low level, L93 using open collector output, so it is neceary to add the pull resistance to output high level.DC motor with gear reductionDC motor drive the car needs to slow down, otherwise to speed up the car, then ran too fast not control, and the deceleration torque is too small and could not run up. We specialize in custom of this type of motor is integrated with the reduction gear and greatly reducing the manufacture difficulty is very suitable for our .L93 comparing two photosensitive resistance, when the imbace (eg side preure runway black) immediately control side of the motor stops rotating, the other side of the motor rotation acceleration, so that the car modification direction, return to the right direction, the whole proce is a closed loop therefore rapid and sensitive control.aembly steps:the first step: circuit part of the basic weldingThe welding circuit part is relatively simple, the welding sequence according to the element height from low to high, the first 8 resistance welding, welding must a to confirm whether the proper welding resistance, polar components such as nsistors, green lights, definitely clear electrolytic polarity as reference element we are photo welding, welding short is the negative side of the insertion pin screen printing shadow, green welding LED note long pin is positive, and the welding is not too long or easy bad welding, D4 D5 R13 R14 can temporarily do not weld, the integrated circuit can be inserted, preliminary ar completion of welding check carefully prevent, be negligent.second step: mechanical aemblythe universal wheel screw is inserted into the hole, and screwed into the universal wheel nut and a universal wheel. the battery box is stuck on the by the double adhesive tape, the lead wire paes the reserved Kong Han received , the red line is connected with the 3 V positive power supply, and the yellow line is connected to the ground.Mechanical part and aembly can be mounted first wheels, wheel consists of three pieces of black acrylic round tablets, aembly prior to exposing protective film, the inside of the wheel center hole grows circular hole, middle of the round plate diameter is relatively small, lateral wheel piece center hole Shiyuan, with two screw nuts fixed set good three round tablets, and black s-tapping screws fixed on the rotating shaft of the engine. Finally the silicone rubber tire sleeve on the wheel. Lead connection lead wire of the motor and the wheel aembly is the of the on the ing position, attention wheels and the edge retaining sufficient clearance, the motor leads are soldered to the . Note that adequately longer lead, to avoid the motor rotation direction error is convenient for changing the lead wire of the order.the third step: the installation of opto-electronic circuitsphotosensitive resistance and light-emitting (attention polarity) is the re installed on the , and the ground distance of about 5mm, the distance between the light-sensitive resistance and light-emitting is also about 5mm. Finally can pa electrical test.the fourth step: Vehicle debuingIn the battery box in 2 AA batteries, switches to dial in the "on", the car driving right re is veling along the direction of the universal wheel, if hold the left side of the photosensitive resistance, the car to the right of the wheel rotation, Keep to the right of photosensitive resistance, the left side of the car wheel must turn, if car vel back can exchange connection of two motors at the same time. as one of the normal back on the other side as long as the exchange of the rear of the motor can be wiring.Due to the difference in lighting, the ture color will be slightly different.Package Include:1x D2-1 Smart Car Kits