Car Side Stickers Wrap Racing Stres For Audi Ford BMW Toyota H Mercedes Benz Auto Vinyl Film Body Door Accessories Decals

Car Side Stickers Wrap Racing Stres For Audi Ford BMW Toyota H Mercedes Benz Auto Vinyl Film Body Door Acceories Decal

Product Name: Car stre side body Decal

Features:100％ and high qualityFunction: S-adhesive and removable,Temperature resistant,no shrinking,waterproof,long-term bility,decoration for your carColor:Black/Gray/Blue/Yellow/Red/Orange/SliverMaterial:PVCSize: 210 * 11.5CM side, shooting is the body on both sides of the complete set oh~Applicable for:All carsNote:1.Item color displayed in photos may be showing slightly different on your computer monitor2.if you Provide patterns, we can support car stickers customizationPackage Includes:2×Car Side Body Decals

Installation notes:

1. Clean the body and keep it dry. 2. In general, first tear the bottom to determine the position to be d, and then slowly tear the bottom paper while sing with a tool (the tool can be card). 3. If the figure is not large (le than 20cm), you can also tear off all the backing paper before pasting. But we must pay attention to tear it slowly, and be careful not to stick the car stickers down or cause accidental adhesion. 4. Ar affixing, repeatedly se and pre for several times, and slowly tear off the nsparent nsfer film. 5. Done. (do not wash the car for 2-)2, Pasting methods of medium-sized stickers (such as door stickers, map stickers, spare tire stickers, etc.):1. Clean the body and keep it dry. (don't do it in the strong wind, rain or sun, you can choose the shelter in the garage, etc.) 2. First tear the bottom to determine the position to be d, and then slowly tear the bottom paper while sing it with a tool (the tool can choose the card). 3. But we must pay attention to tear it slowly, and be careful not to stick the car stickers down or cause accidental adhesion. 4. Ar affixing, repeatedly se and pre for several times, and slowly tear off the nsparent nsfer film. 5. Done. (do not wash the car for 2-, two people are recommended)3, Large car stickers:1. The large stickers are rolled up for delivery when they are delivered. If there are some bubbles or wrinkles in the bottom paper and nsfer film of the stickers, please note that this is normal and does not affect the car stickers. Before the stickers are d, the car stickers should be l on a flat desktop and sed with a ser ( card). 2. It is suested to go to car beauty salon and ask for help. Choose a do it yours buyer, suest posting home to consult the seller. Methods: (dry or wet sticking can be used)(1) Dry method: (the following method is used for the whole big , and the following method is not used for collage) 1. Clean the car body and keep it dry. (don't do it in the strong wind, rain or sun, you can choose the shelter in the garage, etc.) 2. First, compare the car on the car, determine the position to be d, and try to avoid the concave and convex or difficult position. 3. Then you can take a little tape or cut off the nsfer film to fix the car stickers and start to . 4. First, tear off the bottom from the front of the car to determine the position to be d, and then slowly tear off the bottom paper while sing with a tool (the tool can be card). 5. But we must pay attention to tearing slowly, not leaving bubbles, and not sticking the car stickers or causing accidental adhesion. 6. Ar pasting, repeatedly se and pre for several times, and slowly tear off the nsparent nsfer membrane. 7. At the beginning of the later work, first cut the middle of the door with a (gap or opening position), and stick it inward. 8. If there are bubbles, you can try to scratch them again. The big bubbles can be broken directly. If there are small bubbles, you can wait a few days before they are fully bonded. 5. Be sure to check it again when you are finished. (don't wash the car for 2-, 2-3 people are recommended)(2) Wet sticking method - car stickers or large car stickers are applicable [it is recommended to take them to the car beauty shop] steps of wet sticking method - tools: watering can, clean rag, ser, art , air duct 1. Ar cleaning the car body, spray water with the watering can on the body part to be ; mdash; & mdash; is mainly used to reduce the viscosity of the sticker and facilitate the adjustment of the position. 2. Ar deter the position to be d, remove the nsfer film (nsparent adhesive film d on the reflective sticker) and the vehicle sticker from right to left [or from top to bottom] and pre them on the vehicle surface with a rag, then , pre flat with a rag and uncover the bottom paper at the same time. 3. In case of door handle or anti-collision str, the material shall be cut and wrapped or loaded according to the situation. 4. Adjust the general position of the figure in time, and then we off the water and bubbles repeatedly with the ser. When using the ser, se diagonally from right to left. Finally, tear off the nsparent nsfer film. 5. In case of the door and the seam, use the art to p>

Strong requirements: do not expose to the sun within 24 hours, and do not wash the car within 48 hours.

1.We will send out your goods within 1-3WORK DAYSar verification of the payment and confirmation of the order. We always try our best to sh as fast as we can, in case of any delay, we will inform you in advance.

2.If the package is lost and you didn't get the package in 60 days, please contact us first ,we will resend you a new vinyl and new cking number.

3. We will send you cking number ar we send the package ,all the item can be cked online!

4.Usually delivery time will be 14-30 days.

Brazil: Usually delivery day 14-70 days. Other country will be about 14-30 days. Need to proved VAT number, or, we didn't pay for any lo for your parcel.

Ruia also a little bit longer , need 14-40 days usually.

If you don't get the packagein60days or 30 days your packagehave no change in shment, we will help you..

5.If you didn't get the package, and you want us the extend the delivery time limited, you can leave us comment inthe order.

6.We are not responsible for any custom duty or .