5A Solar Panel Regulator Charge Controller 12V 24V Auto Switch

Feature:
●ISO 9001 Certified
●Electronic protection.
●Fully automatic operation.
●PWM charge mode(SOC)
●Micro-controller digital accuracy
●Suitable for all 12/24V lampsSuitable for all 12/24V lamps
●Big terminals,big distance between terminals.
●Double digital LED display, numbers equal to setting
●Temperature compensation(with external temperature sensor)
●MPPT
solar charge controller MPPT10-60: Compared with normal solar charge
controller, this MPPT controller could increase efficiency by 10%-30%.
●This controller can charge and discharge at the same time.
●This MPPT controller has perfect SOC function, control charge current, and supply to the loads.

ProductAttributes:
: Black
Quantity:1Pcs
Size: 133mm x 69.5mm/5.24 x 2.74inch

Safety:
Full consideration to the safety of persons and property has been given when designing the products.
However
the incorrect connection may cause the system breakdown or even safety
accident. For you safety and benefits, the following rules must be
complied during the operation.
●Installation of this product shall be tinder the guidance of the professionals in this field.
●Prevent this controller from water, humidity and insects, to avoid short-circuit.
●Keep children and incapable persons away from the controller.
●Keep
the controller away from electrical heater, heating machine and
high temperature electrica appliances; avoid the controller suffering
from insulation directly.
●Please
check the rated voltage of solar panel, , and loads before
connection. 12V rated voltage is 12V, 24V rated voltage is 24V.
●Make sure connections between positive and negative poles of Solar panels, and Loads are correct.
●The
diameter of connecting cable must be matched with the requirements of
the current. Do not use thinner diameter cable, the thinner diameter.
The larger resistance, this will cause higher temperature and output
powe decreasing.
●The total rated current of solar panel and loads must be smaller than the rated current of the controller.
●Components
of system must be correctly and firmly connected. Prevent the terminals
from oxidation and moldy, to avoid connection trouble.

Function:
●Always keep the on fill voltage condition.
●Prevent the from over-charging.
●Prevent the from over-discharging.
●Prevent the from charging to solar panels during nights.
● polarity protection for .
● polarity protection for solar panels.
●When
the voltage is low, the controller will automatically cut off
the load from the system. If the voltage of is back to normal
and the load will restart working.
●Thunder protection.
●According
to the voltage grade, the controller can automatically set
charge-off voltage, the load-off voltage, the load-restore voltage. (The
is default under 25℃ condition, locked by the CPU procedure,
cannot adjust.)
●The
controller will automatically compensate the temperature of the
charging voltage according to the changes of ambient temperature.

Warning:
Before
connecting to the solar panel, please connect the controller to the
; do not use solar panel supply to the loads directly.

Indicate light and button:
When Red LED (CHARGE) is on, is charged up strongly; When Red LED is flickering, is MPPT
charged up in constant voltage; when Red LED is oft charge off
●When Green LED (LOAD) is on, loads are working; when Green LED (LOAD) is off, loads stop working.
●Three Colorchanging LED (), When light is red, it indicates low voltage, green indicate full charged,
orange indicate normal status.

-changing LED working voltage indicates area:
-changing LED 12V 24V
Red LED 10.5V-11V 21V-22V
Orange LED 10.5~11V-13.7V 21~22V-27.4V
Green LED ≥13.7V ≥ 27.4V

Trouble solution:
Phenomenon: Green LED off, indicator LED is red.
Reason: Low voltage of
Solution:
A:Cut off the , disconnect the load; reconnect the load after the charge become normal.
B: charge problem: Increase the solar panel or change the .

Phenomenon: indicator LED is orange and Load indicator LED is green, the loads cannot work.
Reason:Over load or short-circuit causes the controller inner fuse cut off
Solution: 10-20 minutes after eliminated the malfunction, the fuse will automatically back to working.
v
Note:
1.Duetothelightandscreendifference,theitem'scolormaybeslightlydifferentfromthepictures.Pleaseunderstand.Makesureyoudon'tmindbeforeyoubid.
2.Pleaseallow1-5mmdifferencesduetomanualmeasurement.
3.Do not use lamplight to charge the solar panel (lamplight is too weak to charge)
4. source to replace the solar panel will cause troubles to controller.
5.Choose the suitable wire which diameter should not be too small, please refer to the .
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a