24V 10A Remote Control Motor Switch Controller Tool For Linear Actuator

Name:DC24V 10A Digital Remote Control Motor Switch Controller For Linear Actuator

Model: 593727
Product Description
Material: Plastic case
: white
Operating voltage: 24V
Contact capacity: ≤ 10A
Static operating current: ≤ 6mA
Working temperature: -20 ~ +60 degrees
Receiving sensitivity: -114dBm
Operating frequency: 315MHz
Size
Remote control: 100x40x20mm
Controller: 75x55x25mm

Features:
* Wide range of use, can be applied to motor motor , lamps, access control, industrial control and security industry and fields.
* Features with high confidentiality, stable performance and low consumption
* No need to use the traditional or DIP switch , just the remote control with the receiver controller can be used to achieve matching.
Application: Used in the field of motor motor , lamp, access control, industrial control and security industry.

How to use? (Instructions)
Output: There are four output methods, signal interlock, signal non-lock, signal self-locking, signal lock and self-locking coexist.
(A normally open B public normally closed)

1.Signal interlock: 12 connection, 34 not connected
Press the A key, the A relay is disconnected, and the relay corresponding to the B key is sucked and held, and the key and the D key are operated as follows.

2.The signal is not locked: 12 and 34 are not connected
Press the remote control A key, and the A key corresponding to the relay pull, release the relay after the , press the B key, and B key corresponding to the relay pull, release and disconnect . key and D key this Cycle work.

3. The signal from the lock: 12 connected, 34 connected
Press the remote control A key, and the A key corresponding to the relay to pull and hold, and then press the A key, A relay off. Press the remote control B key, B key corresponding to the relay suction and hold, then press the B key, B relay disconnect, key and D key to work as this cycle.

4. The signal from the lock and non-coexistence: 12 not connected, 34 connected
And the remote control corresponding to the four relays, two self-locking, two non-lock

Study method:
1.Press the receiver on the learning button light and then let go light to go into the learning state, on the remote control of any key to learn, the receiver receives the signal after the light flashes continuously after the study is successful.
2.Clear : long press the button for about 8 seconds to the lights off the clear is successful, clear the learning by the remote control will not be able to use, you must re- before the remote control.


Package include:
1 x Controller
1 x Remote control

Warning: Do not connect the wiring when wiring, so as to avoid short circuit damage to the motherboard, the control of communication for safety should also be off after the good line to confirm the correct and then use .





a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a