220V 1000W Power Supply Delay Power Soft Start Protection Board High Power For

Product descrtion:

●Working voltage: 220V ● Allow the load to be le than 1000W ●Control switch is suitable for self-locking and self-resetting type ●Two protection normally open protection interfaces ●The rated current of the relay is 30A, which can withstand the power below 1000W. ● board is 2MM high-grade fibergla board ●The copper foil of the is 2 ounces ●The size of the is 77.5MM*88MM. ●The distance of four symmetric holes is 69X79.5MM

The main function:

1. Suppre the inrush current of the power amplifier at startup, because the power of the cla A and high power amplifier is large, the load impedance is extremely low, and the power supply filter capacitor capacity is too large, which leads to exceive current at the startup of the power amplifier, which easily damages the rectifier bridge and damage filter capacitor. 2. When the temperature of the heat sink of the power amplifier board exceeds 75 degrees, the board can cut off the power immediately, and the power amplifier will not be overheated and burned. Until the temperature of the heat sink drops below 75 degrees, the power amplifier can be turned back on, otherwise the power amplifier can't be turned on. ● Schematic: For reference only, subject to change without notice.！！！ ●When the start switch KT is preed, if the protection port is normally open (if the port is closed, it cannot be started), the start of the start, the work indicator LED is on, the current limit relay is closed (K01), the current limit module is connected to the 220V loop current limit, delay 3 seconds, the through relay (K02) is closed, the current limit is ended, the delay is 1 second, and the current limiting relay is disconnected. If the startup board is working normally, when any protection port SW is closed, the startup board is turned off. ● This version has a significant improvement with other versions of the soft start board. Other versions of the starter board open the current limit relay without delay when the relay is closed at startup. Due to the mechanical delay of the relay, the 220V circuit will appear. A brief open circuit causes the load to experience a brief inrush current. ●The startup board start switch automatically adapts to the self-locking switch and the self-reset switch, without changing the startup board settings.

Buyer's question:

●What is a self-locking switch and what is a self-resetting switch ● A: Pre the switch to turn on, release the switch to open, it is the self-reset switch; pre the switch to turn on, release or turn on, then pre and then release to open, it is a self-locking switch. ● How big is the start switch? ● A: It can be used within 1A. ● Can the start switch of the starter board be self-locking or self-resetting? ● A: All are ok, the starter board will automatically adapt to the self-locking switch or self-reset switch, without manual intervention. ● If the AC 220V output terminal is not connected to the load (), why is there a 220V voltage output when the startup board is not started? ● A: This is because the arc-extinguishing capacitor is connected in parallel between the relay contacts. As long as the 220V output terminal is connected to the load, it can be soed.

Packaging:

1PC

About shping
Shping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 2 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for e areas,it may take a little longer). 

Special Announcement:
Please fill in the correct and detailed consignee, address and phone number in the order. For fast and correct delivery.If you do not receive order within 30 working days,please feel free to contact Customer Service before leaving Negative and Neutral Feedback, we will do our best to help you resoe the problem.TaxNo, you will only pay what is quoted as total cost at checkout, no more. You are not expected to pay any additional duties or taxes. If you are asked by Customs or our logistic partner to pay duties, please contact our Customer Service .

Your 100% satisfaction is very ant to us
If the product is not on good condition, You can return this product within 14 working days, please contact customer service center before returning.FeedbackYour satisfaction is our first priorityIf you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.