12v 200A universal car battery switch relay integrated wireless remote control disconnect cut off isolator master switches

Thank you for purchasing this product. Please read this manual carefully before . In the daily use of the

car, there will be no power, discharge, leakage, power loss and other situations when starting the car. The reason

is that all kinds of electrical equipment in the car silently use too much battery power, thus reducing the battery life.

This product is installed on the positive or negative pole of the car battery, and the battery is powered off through

the remote control switch, which solves the above troubles of the majority of drivers.

Outstanding features:

I) Automatic mode: when the battery voltage is lower than 12.2V, the power will be

cut off automatically after 3 minutes. When the voltage is 12.2v, the power will be

cut off automatically if the voltage does not reach 13.2v within 3 minutes after the

remote control is turned on. After starting the car, the voltage is higher than 13.2v,

and the remote controller does not work to prevent the battery from being

disconnected due to the false triggering of the driving state. The remote controller

below 13.2v can be turned on and off at any time. Press the lock button of the remote once, the relay can be started

normally when it is powered on. Press the unlock button on the remote once, the power supply of the whole vehicle

will be disconnected.

II) Remote control mode: press the lock button of the remote control once, turn on the power, and it can be started

normally. Press the unlock button on the remote control once, and the power supply of the whole vehicle will be

disconnected. This mode does not detect voltage and does not automatically cut off power.

III) The factory defaults to the automatic mode, The default state is on, which can be started normally.

IV )Mode conversion: press the lock button of the remote control for 5 seconds and then turn to the automatic

mode. press the unlock button for 5 seconds and then turn to the remote control mode. Power on after power

failure to restore automatic mode.

method:

1. Open the engine cover and find out the positive and negative poles of the battery

2. Generally, the negative pile head is selected to install the breaker and judge the

space position where the unit can be pd Remove the negative pile head hoop

3. Install the fitting connecting piece and pile head hoop on the screw column of

the host, regardless of left and right (as shown in the right figure)

4. Screw the pile head hoop of the breaker onto the negative pile head,

and connect the connecting piece with the battery pile just removed

Tighten the head hoop with screws

4. Plug in the power cord. The red wire fork is connected to the positive

pole of the battery, and the black wire fork is connected to the negative

pole of the battery To supply power to the unit, the power consumption

is 2.4W, and the power consumption is less.

Brief introduction

1.A New good design product presant That is a More Convenient Car Battery Disconnect Switch System which can remotely master kill your car power system,A Proper maintenance will extend and protect the battery and engine life

2.Remote operation,Comparing to tranditional battery switch, this Remote Control Wireless Battery Switch Disconnect allows you to move the trigger from under the hood to your hand so that you no need to frequently pick up the hood.

3.Come with 2 light and handy New Style Remote Control.You can even control it in your house,One button control on your dash for the whole car power system, Remote Receiver Stand Current is very low (0.0005A),Universal for DC 12V Car,Truck,Camper Trailer, SUV,Van Small Truck, Agricultural Vehicle ,Trike, Auto Off Road.

4.Integrated design, small size, avoid cumbersome wiring, convenient

SPECIFICATION:

Working voltage: DC 9-15v

Rated current: 200A

Instantaneous current: 500A

Stand current: 0.005A

Package Include,Product composition:

Unit * 1; Remote controller * 2; Pure copper pile head * 1

Aluminum alloy hoops (one positive and one negative)*2;

Copper connecting pieces*2; Instructions Manual*1

There could be some deviations due to manual measurement or slight color difference owing to photographing condition. Thank you for your understanding. If you do not understand what you can contact customer service at any time, I wish you a happy shopping.