Details about DIY Garden Plastic Path Maker Mould Walk Road Mold Paving Cement Brick Black

To clean the concrete garden molds for re-use purpose, spray this concrete mold garden with garden hose. Garden molds can be used again right after you pour the first garden stepping so you do not have to wait. The thick level of concrete can be varying depends on your requirement of garden stepping . A watter mix of concrete for concrete golden molds is used to get garden stepping with ground / lower level, and a stiffer mix of concrete is used to get garden stepping with higher / level. Concrete golden molds work well in all situations and create a very well garden stepping . Material: Plastic : Black Size: approx.40 *40*4cm (1cm=10mm=0.39inch) Measurement Details in the attached picture. Package includes: 1 x Path Maker Mold








How to Make Pavement: Step 1: Lay out the perimeter of the walkway and drive wooden stakes into the ground at each corner. Step 2: For professional results, remove one inch of sod. Save the sod you remove and use it to fill in gaps once the walkway has set. If you plan to use the sod later, set it aside in a cool place and water.
Step 3: The mold comes with directions on how much concrete you need based on the length of walkway youre creating. Mix the concrete, adding to make the walkway resemble cobblestone or brick.
Step 4: Wet the mold with water before you begin adding concrete.
Step 5: Beginning in one corner of the walkway, lay the mold in place.
Step 6: With a bucket or trowel, fill each cavity of the mold with concrete. The concrete should be level with the top of the mold.
Step 7: Smooth the surface with a trowel.
Step 8: In about five to ten minutes, lift the mold. Youre ready to do the section.
Step 9: the mold against the first section and continue building your walkway. By rotating the mold one-quarter turn each time, you create a variation in the pattern.
Step 10: For curves, the outside corner of the mold to the existing walkway. Turn the mold to align with the curve. The mold will overlap the existing concrete on the inside of the curve.
Step 11: Press the mold down, into the existing concrete. Fill the mold with concrete.
Step 12: Remove the mold and blend the combined castings, eliminating cut lines.
Step 13: Position the mold and pour the remaining sections.
Step 14: Sprinkle sand or dry mortar mix on top of your walkway after it is set. Brush it into the joints with a broom.
Step 15: Mist lightly with a garden hose.
Step 16: Place six-mil plastic sheeting over the concrete for two to three days to prevent the surface from drying too quickly and cracking.
Step 17: After your walkway has cured, protect its finish with a concrete sealer. Follow the manufacturers instructions for application. The sealer forms a tough, water-resistant finish that is virtually unaffected by the elements. Note: 1.The real of the item may be slightly different from the pictures on website caused by many factors such as brightness of your and light brightness. 2.Please allow slight deviation for the measurement data. 3.Please allow 1-3cm error due to the hand measurement . Ifyouhaveanyquestions,pleasecontactus. Wishyouhaveahappyshoppingtime!
a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a