Bike Computer Waterproof 20 Functions Speedometer Odometer Cycling Luminous LED Wired/ Wireless MTB

Cycling Computer Name     Bike Computer Waterproof 20 Functions Speedometer Odometer Cycling Luminous LED Wired Wireless Bike Stopwatch 1. Used on two kinds tyre spec 2. Memory function 3.  Speed tendency 4.  SPD          Current Speed 5.  ODO         Odometer 6.  DST          Distance of single trip 7.   MXS          Max speed 8.   AVS          Average speed 9.   TM            Time of ride 10.  CLK        (12h-24h)\Clock    11.  CAL        Calories Level 12. FAT        Fat burn measureement 13. TEM       Temperature 14. SW         Time (seconds watch) 15. Indication for low power 16. Maintenance and reminding function 17. Adaptable for KM\hr or M\hr 18. SETTING WHEEL CYCLING (0mm-99999mm) 19. Default value of odometer setting 20. Auto on \off   Buyer notice The distance between the wireless launcher and themagnetic head is around 1.5mm (The more closer the more sensitive) The distance between the bicycle computer and the magnetic head should be within 60cm   Instructions: 1   About backlight:  During 17:00-7:00,screen will be lighted up for 4 seconds when you press any key , But if you want the screen alwalighted , press both middle and right key  for 1 seconds to keep the screen alwalighted up.Press middle and right key for 1 seconds again to cancel it . 2   About clean the value:  Press the right key to enter into the DST PAT TM mode.under this mode , press the middle key to check the fat and calories value.Press left key for 3 seconds,DST TM MXS AVS FAT and calories comes to '0'. 3  The distance between the bicycle computer and the magnetic head should be within 60cm.The distance between the wireless launcher and themagnetic head is around 1.5mm(The more closer the more sensitive) This model is wireless. There're 4 color ( Red Green Silver ) for your reference.  Contact us to get instruction in English when you receive the computer,we will help you to resolve questions in using.     Battery Installation Remove the battery cover and put a piece of CR2032 battery into the case. Notice: Positive pole (+) should be set upwards. Then cover the the battery cover and screw down.   Sensor and Magnet   Installation Install the sensor onto the front fork of bicycle, and the Magnet is installed onto the steel wire at the same side of wheel. Sensor can be underlaid with back-up plate and use the strap to fasten onto the front fork. It needs to be installed in 60cm distance from the computer. Adjust the comparative location of Sensor and Magnet. The plane must face to the inductor, keep the space to be 1.5mm. Magnet can not be set to the center of Sensor face-to-face, it';s better with the head or tail of Sensor.      Pedestal Installation In the accessories pack there has a strap which can be used to fasten the Seat onto the handlebar, as well we can use the back-up plate to fasten it.   Computer Installation Push the computer along the chute, the button stand fix the computer and hold. Removing it just needs to pull it out in reverse direction along the chute. Check the installation: Turn the front wheel to run, look to the screen to confirm if it';s got signal. If there has no signal or the reaction is not sensitive please adjust the relative location of Sensor and Magnet slightly.   KM/hr / （ M/hr ）Select Press right key to choose KM /hr or M/hr mode. Press the middle key to confirm. Then enter into the Perimeter Setting mode.   Wheel Perimeter Setting The screen shows 2060, select the exact cycle of your bike according to the following list. Press the right key to change the flash number, then press middle key to confirm it. Set from left number to right number. It ranges from 0mm to 9999mm. Then it comes to set the bicycle"II", the screen shows 1860. The same setting operation as bicycle"I". Press the middle key to enter into the weight setting mode.   Weight setting Press the right key to change Kilogram K to Pound L. Press the middle key to confirm it. Default value of weight is 065 kg, press right key to change the number, press middle key to confirm. Press the middle key to enter the Maintenance alert mode.    Maintenance alert Maintenance default value is: 0200, press the right key change the number, press middle key to confirm. Then, it comes to set the Maintenance Reminder of bicycle"II". The default value is 0800. The same setting operation as bicycle"I".   Function:  when distance value reaches to the maintenance setting value, the spanner icon will be twinkling in the screen, press the middle key for 6 seconds to cancel it.   Two Bicycle I / II using Press the middle key for 6 seconds to change bicycle I/II.   Stopwatch function Under the (ODO-TE-CLK) main mode, press the middle key to change to (ODO-TE-SW) mode. In this mode, press left key to start stopwatch, press again to stop it, press right key to clear the value. It ranges from 0:00:00 to 9:59:59.   ODO & Clock Setting Under the ODO Temperature Clock main mode, press left key, you will see the ODO twinkling, press left key again -TE twinkling, press left key again -CLOCK icon twinkling.   1. When ODO twinkling, press left key again for 3 seconds to 1. set ODO value. Press the right key change the number, press the middle key to confirm it, set from right to left number. 2.  2.When TE twinkling, press left key again for 3 seconds to set the temperature unit. Press the right key to change ℃/℉, press the middle key to confirm it.   3.When Clock icon twinkling, press left key again for 3 seconds to set the 12/24 clock. Press the right key to change 12H /24H, press the middle key to confirm it. Then press the right key to change time number, press middle key to confirm it. Press the right key to enter into the DST-FAT-TM mode.   Clear value Press the right key to enter into the DST-FAT-TM mode. Under this mode, press the middle key to check the fat and calories value. Press the left key for 3 seconds, DST, TM, MXS, AVS, FAT and Calories value comes to '0';.   Backlight During 17 :00-07 :00, screen will be lighted up for 4 seconds, when you press any key. But if you want the screen always lighting, press both middle and right key for 1 seconds to keep the screen alwalighted up. Press middle and right key for 1 seconds again to cancel it .   Auto off After 300 seconds no signal inputs the odometer, the screen will turn into OFF state with only clock display. It will be restart only when you press the key again.  

a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a a

We confidently assure you'll be satisfied with what you get.However, If  there's a chance that you are not satisfied with our goods or something else, please let us know before leaving us a Negative feedback. We will try our best for 100% customer satisfaction. Your 5-Star Positive Feedback is much appreciated to us, and your satisfaction is our greatest motivation to move forward.Welcome to Shop Here! Want more Items? Please come & visit our SHOP.

*Shipping and Packaging All it will be double checked and well packed before sending.It will be dispatched within 5 business days after buyers pay for the order. It usually takes about 14 to 18 working days for delivering the package to the destination(for remote areas,it may take a little longer).Your satisfaction is our first priority.

*If you receive the order and it is in good condition,we would be grateful if you would leave us 5 star Positive Feedback for the transaction.