This website uses cookies. For further information on how we use cookies you can read our Privacy and Cookie notice
HomeAutomobileReplacement PartsBrake SystemABSSensorsSHT31 SHT31-D Temperature & Humidity Sensor Module for
GH₵ 54.56
GH₵ 109.1250%
3 units left
Order above GHC 150 on Jumia Express items & get free delivery | regular delivery from GH₵ 20.48 to Tema
0 out of 5
(No ratings available)Promotions
Delivery & Returns
Shipped from abroad
Choose your location
Pickup Station
Delivery Fees GH₵ 20.48
Ready for pickup between 24 October & 29 October when you order within next 13hrs 11mins
Door Delivery
Delivery Fees GH₵ 32.38
Ready for delivery between 24 October & 29 October when you order within next 13hrs 11mins
Return Policy
Free return within 15 days for all eligible items.Details
Warranty
None
Seller Information
Nehami
80%Seller Score
10 Followers
Seller Performance
Shipping speed: Average
Quality Score: Excellent
Customer Rating: Good
Product details
Temperature/Humidity sensors are some of the & highest-accuracy devices you can . And, finally we have some that have a true I2C interface for easy reading. The SHT31-D sensor has an +/-2% relative humidity and +/-0.3 Celsius accuracy for most uses.
Material: plastic
color: purple
Such a lovely chip - so we spun up a breakout board with the SHT31-D and some supporting circuitry such as pullup resistors and capacitors. Each order comes with one fully assembled and tested PCB breakout and a small piece of header. You'll need to solder the header onto the PCB it's fairly easy and takes only a few minutes even for a beginner. Power Pins:
Vin - this is the power pin. The chip can use 2.5-5VDC for power. To power the board, give it the same power as the level of your microcontroller - e.g. for a 5V like , use 5V. For a 3.3V controller like a Pi, connect to 3.3V
GND - common ground for power and I2C pins:
SCL - I2C clock pin, connect to your microcontrollers I2C clock line. This pin has a 10K pullup resistor to Vin
SDA - I2C data pin, connect to your microcontrollers I2C data line. This pin has a 10K pullup resistor to Vin
Other Pins: - This is the I2C address pin. This pin has a 10K pull down resistor to make the default I2C address 0x44. You can tie this pin to Vin to make the address 0x45 - Hardware reset pint. Has a 10K pullup on it to make the chip active by default. Connect to ground to do a hardware reset!
ALR - Alert/Interrupt output. You can set up the sensor to alert you when an event has occured. Check the datasheet for how you can set up the alerts Package Contents:
1 X SHT31-D Temperature Humidity Sensor Only the above package content, other are not included.
Note: Light and different displays may cause the color of the item in the a little different from the real . The measurement allowed error is +/- 1-3cm.
Material: plastic
color: purple
Such a lovely chip - so we spun up a breakout board with the SHT31-D and some supporting circuitry such as pullup resistors and capacitors. Each order comes with one fully assembled and tested PCB breakout and a small piece of header. You'll need to solder the header onto the PCB it's fairly easy and takes only a few minutes even for a beginner. Power Pins:
Vin - this is the power pin. The chip can use 2.5-5VDC for power. To power the board, give it the same power as the level of your microcontroller - e.g. for a 5V like , use 5V. For a 3.3V controller like a Pi, connect to 3.3V
GND - common ground for power and I2C pins:
SCL - I2C clock pin, connect to your microcontrollers I2C clock line. This pin has a 10K pullup resistor to Vin
SDA - I2C data pin, connect to your microcontrollers I2C data line. This pin has a 10K pullup resistor to Vin
Other Pins: - This is the I2C address pin. This pin has a 10K pull down resistor to make the default I2C address 0x44. You can tie this pin to Vin to make the address 0x45 - Hardware reset pint. Has a 10K pullup on it to make the chip active by default. Connect to ground to do a hardware reset!
ALR - Alert/Interrupt output. You can set up the sensor to alert you when an event has occured. Check the datasheet for how you can set up the alerts Package Contents:
1 X SHT31-D Temperature Humidity Sensor Only the above package content, other are not included.
Note: Light and different displays may cause the color of the item in the a little different from the real . The measurement allowed error is +/- 1-3cm.
Specifications
Key Features
- Durable and good quality
- Sensor Module
- SHT31
- SHT31 Module
- SHT31 Sensor Module
- SHT31 Temperature & Humidity Sensor
- The details are as described above
What’s in the box
1 X SHT31-D Temperature Humidity Sensor
Specifications
- SKU: 91954VP1WOHODNAFAMZ
- Model: Sensor Module
- Production Country: China
- Size (L x W x H cm): 3x2x1
- Weight (kg): 0.0015
- Color: multicolor
- Main Material: plastic
- Warranty Address: None
Verified Customer Feedback
This product has no ratings yet.
915 Generation SHT31 SHT31-D Temperature & Humidity Sensor Module for
GH₵ 54.56
GH₵ 109.1250%
Questions about this product?