This website uses cookies. For further information on how we use cookies you can read our Privacy and Cookie notice
HomeAutomobileReplacement PartsFuel SystemFuel InjectionIdle Air Control ValvesDIY Kits 150W 10A Battery Capacity Tester Adjustable Constant Current Electronic Load Discharge Test
Shipped from abroad
915 Generation DIY Kits 150W 10A Battery Capacity Tester Adjustable Constant Current Electronic Load Discharge Test
GH₵ 193.60
GH₵ 387.1950%
2 units left
Order above GHC 150 on Jumia Express items & get free delivery | regular delivery from GH₵ 30.21 to Tema
0 out of 5
(No ratings available)Promotions
Delivery & Returns
Shipped from abroad
Choose your location
Pickup Station
Delivery Fees GH₵ 30.21
Ready for pickup between 24 October & 29 October when you order within next 10hrs 55mins
Door Delivery
Delivery Fees GH₵ 42.11
Ready for delivery between 24 October & 29 October when you order within next 10hrs 55mins
Return Policy
Free return within 15 days for all eligible items.Details
Warranty
None
Seller Information
Nehami
80%Seller Score
10 Followers
Seller Performance
Shipping speed: Average
Quality Score: Excellent
Customer Rating: Good
Product details
The voltage is the range of the power supply voltage value and cannot be adjusted
The current is adjustable for this load test After adjusting the value test with constant current
Test the maximum discharge current of the power supply check whether the power supply current is real and use the power product aging test
Remarks How many W are all in the power dissipation of the NMOS tube and the board voltage is within 300V You can also increase the power in parallel with multiple blocks
The basic circuit form is that TL431 provides reference voltage sense resistor LM324 operational amplifier error amplification with the MOS tube it forms a constant current circuit Use 4 MOS tubes with CPU heat sinkSubstitution Model 80NF70 IRF3205 HRF3250 IRF1010 IRF2807IRF1405 047an08ao etc also available for TO-247 high-power packaging tubes such as IRF 250 260When the board is powered by a 12V switching power supply the wire can be soldered to the right -
Or solder the DC and use 2 wires to short-circuit the - solder joint The 4 rectifier tubes can be welded
The heat sink cannot be connected to the negative metal of the 12V DC and the two cannot be connected to the metal shell at the same time
When the board is connected to the digital dual display meter the power supply of the meter header is connected with the small on the left end of the board 12V
Note Do not connect the thin black wire to GND It will be inaccurate if the current is connected
A-the current thick red and black wire connected to the meter head V is connected to the thin yellow wire voltage test of the meter head IN is the test input terminal and the red and black test terminal is connected to the power supply under test The FAN terminal is connected to the cooling fan
Openthe cap of the knob and tighten the screw
The power tube is coated with thermal grease and screwed directly to the heat sink and the heat sink must be connected power-on debugging Otherwise the power tube may be burned out
ColourAs shown
MaterialPCMetal
Package Contents
1 x battery capacity tester DIY Kits
Only the above package content other products are not included
Note Light reflection and different displays may cause the color of the item in the picture a little different from the real thing The measurement allowed error is - 1-3cm
The current is adjustable for this load test After adjusting the value test with constant current
Test the maximum discharge current of the power supply check whether the power supply current is real and use the power product aging test
Remarks How many W are all in the power dissipation of the NMOS tube and the board voltage is within 300V You can also increase the power in parallel with multiple blocks
The basic circuit form is that TL431 provides reference voltage sense resistor LM324 operational amplifier error amplification with the MOS tube it forms a constant current circuit Use 4 MOS tubes with CPU heat sinkSubstitution Model 80NF70 IRF3205 HRF3250 IRF1010 IRF2807IRF1405 047an08ao etc also available for TO-247 high-power packaging tubes such as IRF 250 260When the board is powered by a 12V switching power supply the wire can be soldered to the right -
Or solder the DC and use 2 wires to short-circuit the - solder joint The 4 rectifier tubes can be welded
The heat sink cannot be connected to the negative metal of the 12V DC and the two cannot be connected to the metal shell at the same time
When the board is connected to the digital dual display meter the power supply of the meter header is connected with the small on the left end of the board 12V
Note Do not connect the thin black wire to GND It will be inaccurate if the current is connected
A-the current thick red and black wire connected to the meter head V is connected to the thin yellow wire voltage test of the meter head IN is the test input terminal and the red and black test terminal is connected to the power supply under test The FAN terminal is connected to the cooling fan
Openthe cap of the knob and tighten the screw
The power tube is coated with thermal grease and screwed directly to the heat sink and the heat sink must be connected power-on debugging Otherwise the power tube may be burned out
ColourAs shown
MaterialPCMetal
Package Contents
1 x battery capacity tester DIY Kits
Only the above package content other products are not included
Note Light reflection and different displays may cause the color of the item in the picture a little different from the real thing The measurement allowed error is - 1-3cm
Specifications
Key Features
The voltage is the range of the power supply voltage value and cannot be adjusted
The current is adjustable for this load test After adjusting the value test with constant current
Test the maximum discharge current of the power supply check whether the power supply current is real and use the power product aging test
Remarks How many W are all in the power dissipation of the NMOS tube and the board voltage is within 300V You can also increase the power in parallel with multiple blocks
The basic circuit form is that TL431 provides reference voltage sense resistor LM324 operational amplifier error amplification with the MOS tube it forms a constant current circuit Use 4 MOS tubes with CPU heat sinkSubstitution Model 80NF70 IRF3205 HRF3250 IRF1010 IRF2807IRF1405 047an08ao etc also available for TO-247 high-power packaging tubes such as IRF 250 260When the board is powered by a 12V switching power supply the wire can be soldered to the right -
The current is adjustable for this load test After adjusting the value test with constant current
Test the maximum discharge current of the power supply check whether the power supply current is real and use the power product aging test
Remarks How many W are all in the power dissipation of the NMOS tube and the board voltage is within 300V You can also increase the power in parallel with multiple blocks
The basic circuit form is that TL431 provides reference voltage sense resistor LM324 operational amplifier error amplification with the MOS tube it forms a constant current circuit Use 4 MOS tubes with CPU heat sinkSubstitution Model 80NF70 IRF3205 HRF3250 IRF1010 IRF2807IRF1405 047an08ao etc also available for TO-247 high-power packaging tubes such as IRF 250 260When the board is powered by a 12V switching power supply the wire can be soldered to the right -
What’s in the box
1 x battery capacity tester DIY Kits
Specifications
- SKU: 91954VP34J6QFNAFAMZ
- Model: battery capacity tester
- Production Country: China
- Size (L x W x H cm): 15x15x5
- Weight (kg): 0.1655
- Color: multicolor
- Warranty Address: None
Verified Customer Feedback
This product has no ratings yet.
915 Generation DIY Kits 150W 10A Battery Capacity Tester Adjustable Constant Current Electronic Load Discharge Test
GH₵ 193.60
GH₵ 387.1950%
Questions about this product?