433Mhz DC 12V 20A 4CH Relay Module Receiver EV1527 Wireless Remote Control Switch 433Mhz for DC Motor DIY

433Mhz DC 12V 20A 4CH Relay Module Receiver EV1527 Wireless Remote Control Switch 433Mhz for DC Motor DIY

• I am an international seller，100% brand new and of high quality

Our shop sells the most popular 3C consumer electronics products,such as mobile phone accessories,computer accessories,game peripherals,smart wearables,and follow the most popular fashion trends. If you like our products,please follow us,become our follower and fan.We will provide you with the most popular products to satisfy your fashion shopping experience.Frequency : 433 MHzChannel : 4Model Number : Wireless Remote ControlWireless Communication : RFUse : Universal,Lighting,Electric Door,Automated curtains,SWITCHBrand Name : kebiduOrigin : Mainland ChinaMatching Mode : Intelligent Learning eWorking Voltage : DC 12VFeature 1 : Wireless Remote ControlFeature 2 : DC 12V 4CH Relay ReceiverFeature 3 : 433MHz DC 12V 4CH Receiver Rf TransmitterFeature 4 : For Garage/Gate/Motor/Light/LampFor Receiver Module :Working Voltage: DC 12VProduct Type: 4 Channel Remote Control SwitchRF Working Mode: ASK SuperheterodyneReceptionModulation Mode:ASKWorking Mode: Momentary/Toggle/Latched, etc.Matching Mode: Intelligent Learning e.RF Frequency: 433MHzReceiving Sensitivity: >104dbmRemote ize: 60*30 mmFrequency: 433.92 MHzBattery: Including batteryColor: Blacke: 1527 learning eRange: about 50-100m in open spaceOperation Introduction:About Working Mode:1. Momentary/Joggle: Press and hold->On; Release->OffKeep pressing one button, the corresponding channel is working /on; Release your finger is stop/OFF. (4 channel switch(receiver) need 4 button remote control (transmitter )2. Toggle/Self-Lock: Press->On; Press again->Off Press one button for one time, the corresponding channel is working/on; Press the same button again to stop/OFF. (4 channel switch(receiver) need 4 button remote control (transmitter).3. Latched/Inter-Lock: Press->on; Press other button->OffPress one button for one time, the corresponding channel is working/on; Press another button is stop/OFF(At the same time, another corresponding channel works). (4 channel switch( receiver) need 4 buttons remote control (transmitter).The Setting of Working Mode:1.Momentary Mode: Pressing the learning key button on the receiver board once (LED Indicator on receiver board will signaling simultaneously), then press any of the remote button, signaling three times by remote's LED indicator means setting Momentary Mode successfully.2. Toggle Mode: Pressing two times the learning key button on the receiver board twice(LED Indicator on receiver board will signaling simultaneously),then press any of the remote button , signaling three times by remote's LED means setting Toggle Mode successfully.3.Latched Mode: Pressing the learning key button on the receiver board three times (LED Indicator on receiver board will signaling simultaneously), then press first remote button, follow on second remote button, signaling three times by remote's LED indicator means setting Latching Mode successfully (first button stands for on, second button stands for off ).4.2CH Momentary + 2CH Toggle: Pressing the learning key button on the receiver board four times(LED Indicator on receiver board will signaling simultaneously),then press any of the remote button , signaling three times by remote's LED indicator means setting successfully.5. 2CH Momentary + 2CH Latched: Pressing the learning key button on the receiver board five times(LED Indicator on receiver board will signaling simultaneously), then press any of the remote button, signaling three times by remote's LED indicator means setting successfully .6. 2CH Toggle + 2CH Latched: Pressing the learning key button on the receiver board six times(LED Indicator on receiver board will signaling simultaneously), then press any of the remote button, signaling three times by remote's LED indicator means setting successfully.7. 2CH Latching + 2CH Latched: Pressing the learning key button on the receiver board seven times(LED Indicator on receiver board will signaling simultaneously), then press any of the remote button, signaling three times by remote's LED indicator means setting successfully.8. Deleting Existing Remote Controls Data: Pressing the learning key button on the receiver board eight times, the LED Indicator on receiver board will flash for eight times, it means that the existing remote controls are deleted successfully.