2.4G TY24D Wifi Wireless Remote Control Module Transmitter and Receiver Board Transmission Reception Communication 6 Channel

2.4G TY24D Wifi Wireless Remote Control Module Transmitter and Receiver Board Transmission Reception Communication 6 Channel

• I am an international seller

Our shop sells the most popular 3C consumer electronics products,such as mobile phone accessories,computer accessories,game peripherals,smart wearables,and follow the most popular fashion trends. If you like our products,please follow us,become our follower and fan.We will provide you with the most popular products to satisfy your fashion shopping experience.Package : TQFPis_customized : YesModel Number : Wireless Remote Control ModuleOperating Temperature : normalDissipation Power : lowSupply Voltage : 3.3VApplication : ComputerCondition : NewType : Voltage RegulatorBrand Name : Your CeeOrigin : Mainland ChinaTY24D-TX is the transmitting module, TY24D-RX is the receiving module. The transmitting module only needs to provide 3.3V power supply and transmitting button and one LED as the transmitting status indication. The output port corresponding to the receiving module can output the level signal, and the module has the output status. Select to select the latched or non-latched mode. The transmitter has 6 input ports, corresponding to the 6 output ports received, up to 64 channels. The 6 channels can work independently or at the same time without interference. The module adopts the learning e mode and the module has a single ID number. A remote controller can arbitrarily learn the ID address and data channel of a receiving module. The receiving module has a learning and prohibiting learning function to prevent illegal learning of the same type of remote controller, and the application security level is high. The module is small in size, low in power consumption, and easy to use. The transmitter module only needs to design a button board according to the remote control shell. The receiving module has no peripheral parts, and does not need any programming. The ing chip is very convenient and simple to use, and multiple sets of products can be simultaneously Use without interfering with each other, effectively solve the problem that 315/433M remote control products cannot be launched at the same time.RX Mode Conversion Function:Latch mode: RX output port is normally 0 level state, press the button once, receive the output high level and latch, press the button again, the receiving output becomes 0 level, the B8 port needs to be connected to GND.Non-latching mode: Press and hold the transmit button, receive the output high level, release the button, and receive 0 level. The B8 port needs to be connected to VDD.?Pair e and Disable e Function:?TX and RX must be used for the e. RX can only identify the TX with successful e. After the e is successful, the B7 e port must be disconnected (floating) to prohibit other TX pairs, preventing other remote controllers from illegally controlling the e. Your receiving device. The receiving pair e port does not limit the number of pairs of the remote controller (multiple send 1 version) in the allowable e status, allowing several remote control e to be determined by the owner. If the receiving module (RX) is replaced after the e is ed, the remote control (TX) needs to be re-ed. The remote control can only control its own receiving device. If a remote controller and its receiving device are paired with the e, then learn the other. Receiving the device and learning successfully, the receiving device will no longer receive the information of the remote controller and automatically clear the remote controller. If you need to use this remote control, you need to re-receive the device pair e. The password is a unique 32-bit address that is sent to the other party when the e is paired. Each transmission or reception can only store a unique password. If the e is re-ed, the password will be cleared.?Testing and use:?After the e is successful, press the B1-B6 transmit button to receive the B1-B6 port output high level. Use the LED to display whether the output function is normal. The open reference distance is about 50m. The launch is usually in low power mode. Press the launch button. The emission current. The receiving module can provide 2mA output current to drive 3V LED. If you need to add power drive circuit to drive other large loads, the module power supply can't be reversed, and the voltage can't exceed 3.6V. Otherwise, the device needs to provide stable voltage. A 47Omega resistor and a 10UF capacitor are placed in front of VDD to power the module. The module is a built-in antenna of the PCB. The antenna must leave the steel plate of the main board. Otherwise, the transmission and receiving distance will be affected. The module can be soldered with pin headers, and the module cannot be reflowed.